��ࡱ�>��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������{ ��T�bjbj�� 1����f���f�{����������H#H#H#H#H#����\#\#\#8�#��$\\#H��$L(%>%>%>%&��&<' �G�G�G�G�G�G�G$�I�tL��GH#='&&='='�GH#H#>%>%��G�3�3�3='fH#>%H#>%g>, �3='�G�3�336t�6>%�������'{������(J�6S>�G0H�6pM�- pM�6pMH#�6�='='�3='='='='='�G�G�0�='='='H='='='='��������������������������������������������������������������������pM='='='='='='='='='�X ": SECTION 074213.13 - FORMED METAL WALL PANELS TIPS: To view non-printing Editor's Notes that provide guidance for editing, click on MasterWorks/Single-File Formatting/Toggle/Editor's Notes. Revise this Section by deleting and inserting text to meet Project-specific requirements. GENERAL SUMMARY Section Includes: Exposed-fastener, lap-seam metal wall panels. Concealed-fastener, lap-seam metal wall panels. Metal liner panels. Related Requirements: Retain subparagraphs below to cross-reference requirements Contractor might expect to find in this Section but are specified in other Sections. Section�074213.16 "Metal Plate Wall Panels" for solid metal plate wall panels. Section�074213.19 "Insulated Metal Wall Panels" for foamed-in-place, laminated and honeycomb insulated metal wall panels. Section�074213.23 "Metal Composite Material Wall Panels" for metal-faced composite wall panels. Section�074293 "Soffit Panels" for metal panels used in horizontal soffit applications. PREINSTALLATION MEETINGS Retain "Preinstallation Conference" Paragraph below if Work of this Section is extensive or complex enough to justify a conference. Preinstallation Conference: Conduct conference at [Project site] .如有需要,保留以下分段;修改为包含更具体的会议信息。与业主、建筑师、业主保险公司(如适用)、金属面板安装商、金属面板制造商代表、结构支撑安装商以及与金属面板有接口或影响的安装商(包括门、窗和百叶窗安装商)会面。审查并确定施工进度,确认材料、安装人员、设备和设施的可用性,以确保施工进度和避免延误。审查与金属面板安装相关的方法和程序,包括制造商的书面说明。检查支撑条件是否符合要求,包括结构构件之间的对齐和连接。检查闪光,特殊壁板细节,墙壁穿透,开口,以及其他影响金属板的建筑状况。审查有关保险、证书、测试和检查的法规和要求(如适用)。在安装期间和安装后检查金属面板组装的临时保护要求。 Review of procedures for repair of metal panels damaged after installation. Document proceedings, including corrective measures and actions required, and furnish copy of record to each participant. ACTION SUBMITTALS Action submittals are submittals requiring responsive action and return of reviewed documents to Contractor. Product Data: For each type of product. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for each type of panel and accessory. Sustainable Design Submittals: Retain "Product Data" Subparagraph below to require minimum recycled content for LEED 2009, MRc�4, "Recycled Content." Product Data: For recycled content, indicating postconsumer and preconsumer recycled content and cost. Shop Drawings: Include fabrication and installation layouts of metal panels; details of edge conditions, joints, panel profiles, corners, anchorages, attachment system, trim, flashings, closures, and accessories; and special details. Accessories: Include details of the flashing, trim, and anchorage systems, at a scale of not less than 3 inches per 12 inches (1:5). Calculations: Include calculations with registered engineer seal, verifying wall panel and attachment method; resist wind pressures imposed on them pursuant to applicable building codes. Retain "Samples for Initial Selection" and "Samples for Verification" paragraphs below for two-stage Samples. Samples for Initial Selection: For each type of metal panel indicated with factory-applied finishes. Include Samples of trim and accessories involving color selection. Samples for Verification: For each type of exposed finish, prepared on Samples of size indicated below: Metal Panels: 12 inches (305 mm) long by actual panel width. Include fasteners, closures, and other metal panel accessories. INFORMATIONAL SUBMITTALS Information submittals are submittals that require review by Architect, but they do not require Architect's responsive action and return of reviewed documents to Contractor, provided submittals comply with requirements. If rejected, submittals with responsive action must be returned to Contractor. Coordinate "Qualification Data" Paragraph below with qualification requirements in Section�014000 "Quality Requirements" and as may be supplemented in "Quality Assurance" Article. Qualification Data: For manufacturer and Installer. Product Test Reports: For each product, for tests performed by a qualified testing agency. Retain "Field quality-control reports" Paragraph below if Contractor is responsible for field quality-control testing and inspecting. Field quality-control reports. Sample Warranties: For special warranties. CLOSEOUT SUBMITTALS Maintenance Data: For metal panels to include in maintenance manuals. QUALITY ASSURANCE Qualifications: Manufacturer: A firm experienced in manufacturing products or systems similar to those indicated for this Project and with a record of successful in-service performance, as well as sufficient production capacity to produce required units. As applicable, procure products from manufacturers able to meet qualification requirements, warranty requirements, and technical or factory-authorized service representative requirements. Installer: An entity that employs installers and supervisors who are trained and approved by manufacturer. Mockups: Build mockups to verify selections made under Sample submittals, to demonstrate aesthetic effects, and to set quality standards for fabrication and installation. Retain first subparagraph below for large-scale mockup. Indicate portion of building represented by mockup on Drawings or draw mockup as separate element. Revise to suit Project or if larger mockup is needed for field performance testing. Build mockup of typical metal panel assembly [as indicated on Drawings] ,包括[角,][拱腹,]支撑,附件和附件。对样机的批准不构成对样机中包含的合同文件的偏差的批准,除非业主通过变更订单明确批准此类偏差。如果你想对014000节“质量要求”中关于拆除和移除模型的默认要求做一个例外,请保留下面的分段。根据要求,批准的模型可能成为完成工作的一部分,如果在实质性完成时没有受到干扰。交付、储存和处理交付部件、金属面板和其他制成品,以避免损坏或变形。包装金属板在运输和搬运过程中保护。卸载、储存和竖立金属板的方式应防止弯曲、翘曲、扭曲和表面损坏。在平台或托盘上水平堆放金属板,并盖上合适的防风雨通风罩。储存金属板,确保干燥,有正面坡度,排水。不要储存与其他材料接触的金属面板,可能导致染色,凹痕或其他表面损伤。 Remove strippable protective covering on metal panels until installation. Remove as panels are installed. Verify that film is completely removed from installed panels. FIELD CONDITIONS Weather Limitations: Proceed with installation only when existing and forecasted weather conditions permit assembly of metal panels to be performed in accordance with manufacturers' written instructions and warranty requirements. COORDINATION Coordinate metal panel installation with rain drainage work, flashing, trim, construction of soffits, and other adjoining work to provide a leakproof, secure, and noncorrosive installation. WARRANTY When warranties are required and available, verify with Owner's counsel that special warranties stated in this article are not less than remedies available to Owner under prevailing local laws. Special Galvalume Substrate Warranty: Manufacturer agrees to repair or replace components of metal panel systems that fail in materials or workmanship within specified warranty period. Failures include, but are not limited to, the following: Structural failures including rupturing or perforating. Deterioration of metals and other materials beyond normal weathering. Warranty Period: 20 years and six months from date of Substantial Completion. Special Warranty on Panel Finishes: Manufacturer agrees to repair finish or replace metal panels that show evidence of deterioration of factory-applied finishes within specified warranty period. Exposed Panel Finish: Deterioration includes, but is not limited to, the following: Color fading more than 5�Hunter units when tested in accordance with ASTM�D2244. Chalking in excess of a No.�8 rating when tested in accordance with ASTM�D4214. Cracking, chipping, peeling, or failure of paint to adhere to bare metal. Finish Warranty Period: 20 years from date of Substantial Completion. PRODUCTS PERFORMANCE REQUIREMENTS Retain "Recycled Content" Paragraph below to specify recycled content if required. An alternative method of requiring recycled content is to retain requirement in Project's Division�01 sustainable design requirements Section that gives Contractor the option and responsibility to determine how recycled content requirements will be met. Recycled Content: Postconsumer recycled content plus one-half of preconsumer recycled content not less than 29 percent. For technical guidance based on panel profiles being used, see chart atHYPERLINK "//www.efxbank.com/resources/testing-summary-chart/"www.efxbank.com/resources/testing-summary-chart. Structural Performance: Provide metal panel systems capable of withstanding the effects of the following loads, based on testing in accordance with ASTM�E1592: Wind Loads: As indicated on Drawings. Deflection Limits: For wind loads, no greater than 1/240 of the span. CONCEALED-FASTENER, LAP-SEAM METAL WALL PANELS Provide factory-formed metal panels designed to be field assembled by lapping and interconnecting side edges of adjacent panels and mechanically attaching through panel to supports using concealed fasteners in side laps. Include accessories required for weathertight installation. Insert drawing designation. Use these designations on Drawings to identify each product. Wide-Reveal-Joint, Concealed-Fastener Metal Wall Panels :用[垂直] [横向]面板边缘和面板边缘之间的阶梯式轮廓形成,导致面板之间的宽显示接头。保留“设计基础产品”分段和下面的制造商名单,以要求特定产品或所列制造商的可比产品。基础产品产品:符合要求,提供Berridge Manufacturing Co。BR-12或可比产品之一:保留在下面的“金属涂层钢板”涂层中的首选;保留丙烯酸涂层的镀锌的第二种选择。金属涂层钢板:铝 - 锌合金涂层钢板符合ASTM�A792/ A792M,[Class│AZ50(Class│AZM150)] [Class│AZ55(Class│AZM155)]涂层指定;结构质量。由线圈涂层方法预先符合ASTM�A755/ A755M。标称厚度:[0.024英寸(0.61 mm)] [0.029英寸(0.74 mm)]。表面:光滑,平坦。 Exterior Finish: [Two-coat] [Metallic] fluoropolymer. For color options, see chart at  HYPERLINK "//www.efxbank.com/colors/" www.efxbank.com/colors/. Color: [As indicated by manufacturer's designations] [Match Architect's samples] [As selected by Architect from manufacturer's full range] .面板覆盖:12英寸(305毫米)。面板高度:0.875英寸(22毫米)。对于覆层上的金属墙板,保留下面的“自粘、高温衬垫”或“毡衬垫”段落。自粘的、高温衬垫只能在易渗漏的墙体开口闪水条件下使用,在墙体的其余部分使用毛毡;或者可以在整个墙体区域上应用衬垫。“自粘、高温衬垫”段中列出的衬垫适用于与金属壁相关的高温应用。如果不需要高温衬垫,则进行修改。与衬垫制造商一起,验证在墙面应用和直接在波纹金属甲板上使用的可接受性。有关Berridge支持的认可衬垫制造商的列表,请参见 HYPERLINK“//www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf”www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf。 Self-Adhering, High-Temperature Underlayment: Provide self-adhering, cold-applied, sheet underlayment, a minimum of 40 mils (1.02 mm) thick, consisting of slip-resistant, polyethylene-film top surface laminated to a layer of butyl or SBS-modified asphalt adhesive, with release-paper backing. Provide primer when recommended by underlayment manufacturer. Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from manufacturers listed or a comparable product from other manufacturers. Manufacturers: Subject to compliance with requirements, provide products by one of the following: GCP Applied Technologies Inc.; Grace Ultra. Mid-States Asphalt; Quick Stick HT Pro. Polyglass USA, Inc.; Polystick MTS. SOPREMA; Lastobond Shield HT. Tamko Building Products LLC; TW Underlayment or TW Metal & Tile Underlayment. .热稳定性:在240degīf(116deg�c)测试后稳定;ASTM�D1970。低温柔韧性:在减去20degīf的测试后通过(29deg�c);ASTM�D1970。如果没有使用自粘附,高温衬垫,保留下面的“感觉障碍”段落。毛毡界限:ASTM�D226/ D22M,型�II(No.Ing�30),沥青饱和有机毡。杂项材料使用ASTM�A653/ A653M用于16型尺寸的次帧;ASTM�A792/ A792M用于22或24级或24级次帧。杂项金属次焦和毛刺:ASTM�C645,冷成型金属涂层钢板,ASTM�A653/ A653M,G90(Z275)热浸镀锌涂层指定或ASTM�A792/ A792M,Class�az50(类AZM150)除非另有说明,否则铝 - 锌合金涂层指定。 Provide manufacturer's standard sections as required for support and alignment of metal panel system. Retain panel accessories, flashing, and trim as required and coordinate with those specified in Section�076200 "Sheet Metal Flashing and Trim." Panel Accessories: Provide components required for a complete, weathertight panel system including trim, copings, fasciae, mullions, sills, corner units, clips, flashings, sealants, gaskets, fillers, closure strips, and similar items. Match material and finish of metal panels unless otherwise indicated. Closures: Provide closures at eaves and rakes, fabricated of same metal as metal panels. Backing Plates: Provide metal backing plates at panel end splices, fabricated from material recommended by manufacturer. Closure Strips: Closed-cell, expanded, cellular, rubber or crosslinked, polyolefin-foam or closed-cell laminated polyethylene; minimum 1-inch- (25-mm-) thick, flexible closure strips; cut or premolded to match metal panel profile. Provide closure strips where indicated or necessary to ensure weathertight construction. Flashing and Trim: Provide flashing and trim formed from same material as metal panels as required to seal against weather and to provide finished appearance. Locations include, but are not limited to, bases, drips, sills, jambs, corners, endwalls, framed openings, rakes, fasciae, parapet caps, soffits, reveals, and fillers. Finish flashing and trim with same finish system as adjacent metal panels. Panel Fasteners: Zinc-coated steel, corrosion-resistant steel, zinc cast head, or nylon capped steel; type and size as approved for applicable loading requirements. Provide long-life exposed fasteners with heads matching color of metal panels by means of factory-applied coating. Provide EPDM or PVC sealing washers for exposed fasteners. For approved sealant guidance, see approved list at  HYPERLINK "//www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf" www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf. Panel Sealants: Provide sealant types recommended by manufacturer that are compatible with panel materials, are nonstaining, and do not damage panel finish. Sealant Tape: Pressure-sensitive, 100 percent solids, gray polyisobutylene compound sealant tape with release-paper backing. Provide permanently elastic, nonsag, nontoxic, nonstaining tape 1/2 inch (13 mm) wide and 1/8 inch (3 mm) thick. Joint Sealant: ASTM�C920; elastomeric polyurethane or silicone sealant; of type, grade, class, and use classifications required to seal joints in metal panels and remain weathertight; and as recommended in writing by metal panel manufacturer. Butyl-Rubber-Based, Solvent-Release Sealant: ASTM�C1311. FABRICATION Fabricate and finish metal panels and accessories at the factory, by manufacturer's standard procedures and processes, as necessary to fulfill indicated performance requirements demonstrated by laboratory testing. Comply with indicated profiles and with dimensional and structural requirements. Provide panel profile, including major ribs and intermediate stiffening ribs, if any, for full length of panel. Sheet Metal Flashing and Trim: Fabricate flashing and trim to comply with manufacturer's written instructions and recommendations in SMACNA's "Architectural Sheet Metal Manual" that apply to design, dimensions, metal, and other characteristics of item indicated. Form exposed sheet metal accessories that are without excessive oil-canning, buckling, and tool marks and that are true to line and levels indicated, with exposed edges folded back to form hems. Seams for Aluminum: Fabricate nonmoving seams with flat-lock seams. Form seams and seal with epoxy seam sealer. Rivet joints for additional strength. Seams for Other Than Aluminum: Fabricate nonmoving seams in accessories with flat-lock seams. Tin edges to be seamed, form seams, and solder. Sealed Joints: Form nonexpansion, but movable, joints in metal to accommodate sealant and to comply with SMACNA standards. Conceal fasteners and expansion provisions where possible. Exposed fasteners are not allowed on faces of accessories exposed to view. Fabricate cleats and attachment devices from same material as accessory being anchored or from compatible, noncorrosive metal recommended in writing by metal panel manufacturer. Size: As recommended by SMACNA's "Architectural Sheet Metal Manual" or metal wall panel manufacturer for application, but not less than thickness of metal being secured. FINISHES Protect mechanical and painted finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in same piece are unacceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. Steel Panels and Accessories: Retain "Two-Coat Fluoropolymer" or "Metallic Fluoropolymer" Subparagraph below. Verify availability of finishes for products specified. If retaining both, indicate location of each on Drawings or by inserts. To obtain a proprietary finish system, insert names of coating manufacturers and products. Two-Coat Fluoropolymer: AAMA�621. Fluoropolymer finish containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75 mil (0.0191 mm), plus or minus 0.05 mil (0.0013 mm), over 0.2 mil (0.0051 mm) plus or minus 0.05-mil (0.0013-mm) primer coat, to provide a total dry film thickness of 0.95 mil (0.0241 mm), plus or minus 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions[�for seacoast and severe environments]. Metallic Fluoropolymer: AAMA�621. Two-coat fluoropolymer finish with suspended metallic flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75 mil (0.0191 mm), plus or minus 0.05 mil (0.0013 mm), over 0.2 mil (0.0051 mm) plus or minus 0.05-mil (0.0013-mm) primer coat, to provide a total dry film thickness of 0.95 mil (0.0241 mm), plus or minus 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions[�for seacoast and severe environments]. Finish in "Concealed Finish" Subparagraph below is frequently used as a factory finish for interior surfaces. Concealed Finish: Apply pretreatment and manufacturer's standard white or light-colored acrylic or polyester backer finish consisting of prime coat and wash coat with a minimum total dry film thickness of 0.35 mil (0.009 mm). Aluminum Panels and Accessories: Retain "Two-Coat Fluoropolymer" or "Metallic Fluoropolymer" Subparagraph below. Verify availability of finishes for products specified. If retaining both, indicate location of each on Drawings or by inserts. To obtain a proprietary finish system, insert names of coating manufacturers and products. Revise or insert additional testing requirements in both subparagraphs if performance levels indicated in AAMA�2605 are insufficient. Two-Coat Fluoropolymer: AAMA�2605. Fluoropolymer finish containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75 mil (0.0191 mm), plus or minus 0.05 mil (0.0013 mm), over 0.2 mil (0.0051 mm) plus or minus 0.05-mil (0.0013-mm) primer coat, to provide a total dry film thickness of 0.95 mil (0.0241 mm), plus or minus 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions[�for seacoast and severe environments]. Metallic Fluoropolymer: AAMA�2605. Two-coat fluoropolymer finish with suspended metallic flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75 mil (0.0191 mm), plus or minus 0.05 mil (0.0013 mm), over 0.2 mil (0.0051 mm) plus or minus 0.05-mil (0.0013-mm) primer coat, to provide a total dry film thickness of 0.95 mil (0.0241 mm), plus or minus 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions[�for seacoast and severe environments]. EXECUTION EXAMINATION Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances, metal panel supports, and other conditions affecting performance of the Work. Retain one or both subparagraphs below. Examine wall framing to verify that girts, angles, channels, studs, and other structural panel support members and anchorage have been installed within alignment tolerances required by metal wall panel manufacturer. Examine wall sheathing to verify that sheathing joints are supported by framing or blocking and that installation is within flatness tolerances required by metal wall panel manufacturer. Retain subparagraph below with subparagraph above for systems that depend on air- or water-resistive barriers to prevent air infiltration or water penetration. Verify that air- or water-resistive barriers have been installed over sheathing or backing substrate to prevent air infiltration or water penetration. Examine roughing-in for components and systems penetrating metal panels to verify actual locations of penetrations relative to seam locations of metal panels before installation. Proceed with installation only after unsatisfactory conditions have been corrected. PREPARATION Miscellaneous Supports: Install subframing, furring, and other miscellaneous panel support members and anchorages in accordance with ASTM�C754 and metal panel manufacturer's written instructions. METAL PANEL INSTALLATION General: Install metal panels in accordance with manufacturer's written instructions in orientation, sizes, and locations indicated. Install panels perpendicular to supports unless otherwise indicated. Anchor metal panels and other components of the Work securely in place, with provisions for thermal and structural movement. Shim or otherwise plumb substrates receiving metal panels to be level to 1/4 inch in 20�ft. (6 mm in 6.1�m). Flash and seal metal panels at perimeter of all openings. Fasten with self-tapping screws. Do not begin installation until air- or water-resistive barriers and flashings that will be concealed by metal panels are installed. Install screw fasteners in predrilled holes. Locate and space fastenings in uniform vertical and horizontal alignment. Install flashing and trim as metal panel work proceeds. Locate panel splices over, but not attached to, structural supports. Stagger panel splices and end laps to avoid a four-panel lap splice condition. Align bottoms of metal panels and fasten with blind rivets, bolts, or self-tapping screws. Fasten flashings and trim around openings and similar elements with self-tapping screws. Provide weathertight escutcheons for pipe- and conduit-penetrating panels. Fasteners: Steel Panels: Use stainless steel fasteners for surfaces exposed to the exterior; use galvanized steel fasteners for surfaces exposed to the interior. Aluminum Panels: Use stainless steel fasteners for surfaces exposed to the exterior; use stainless steel fasteners for surfaces exposed to the interior. Metal Protection: Where dissimilar metals contact each other or corrosive substrates, protect against galvanic action as recommended in writing by metal panel manufacturer. Lap-Seam Metal Panels: Fasten metal panels to supports with fasteners at each lapped joint at location and spacing recommended in writing by manufacturer. Lap ribbed or fluted sheets one full rib. Apply panels and associated items true to line for neat and weathertight enclosure. Provide long-life metal-backed washers under heads of exposed fasteners bearing on weather side of metal panels. Locate and space exposed fasteners in uniform vertical and horizontal alignment. Use proper tools to obtain controlled uniform compression for positive seal without rupture of washer. Install screw fasteners with power tools having controlled torque adjusted to compress washer tightly without damage to washer, screw threads, or panels. Install screws in predrilled holes. Flash and seal panels with weather closures at perimeter of all openings. Retain "Watertight Installation" Paragraph below for hydrostatic (watertight) panel installation; delete for water-shedding panel installations. Contact Berridge to verify weathertight warranty requirements and which products are capable of achieving it. Watertight Installation: Apply a continuous ribbon of sealant or tape to seal lapped joints of metal panels, using sealant or tape as recommend by manufacturer on side laps of nesting-type panels; and elsewhere as needed to make panels watertight. Provide sealant or tape between panels and protruding equipment, vents, and accessories. At panel splices, nest panels with minimum 6-inch (152-mm) end lap, sealed with sealant and fastened together by interlocking clamping plates. Metal Liner Panels: Install panels on [exterior side of girts, with girts exposed to the interior] [interior side of girts with flush appearance on the inside]. Accessory Installation: Install accessories with positive anchorage to building and weathertight mounting, and provide for thermal expansion. Coordinate installation with flashings and other components. Install components required for a complete metal panel system including trim, copings, corners, seam covers, flashings, sealants, gaskets, fillers, closure strips, and similar items. Provide types indicated by metal wall panel manufacturer; or, if not indicated, provide types recommended by metal panel manufacturer. Flashing and Trim: Comply with performance requirements, manufacturer's written installation instructions, and SMACNA's "Architectural Sheet Metal Manual." Provide concealed fasteners where possible, and set units true to line and level as indicated. Install work with laps, joints, and seams that are permanently watertight. Install exposed flashing and trim that is without buckling and tool marks, and that is true to line and levels indicated, with exposed edges folded back to form hems. Install sheet metal flashing and trim to fit substrates and achieve waterproof performance. Expansion Provisions: Provide for thermal expansion of exposed flashing and trim. Space movement joints at a maximum of 10 ft. (3�m) with no joints allowed within 24 inches (610 mm) of corner or intersection. Where lapped expansion provisions cannot be used or would not be sufficiently waterproof, form expansion joints of intermeshing hooked flanges, not less than 1 inch (25 mm) deep, filled with mastic sealant (concealed within joints). FIELD QUALITY CONTROL Retain "Testing Agency" Paragraph below to identify who will perform tests and inspections. If retaining second option below, retain "Field quality-control reports" Paragraph in "Informational Submittals" Article. Testing Agency: [Owner will engage] [Engage] a qualified testing agency to perform tests and inspections. Retain "Manufacturer's Field Service" Paragraph below to require a factory-authorized service representative to perform tests and inspections. Manufacturer's Field Service: Engage a factory-authorized service representative to test and inspect completed metal wall panel installation, including accessories. Remove and replace metal wall panels where tests and inspections indicate that they do not comply with specified requirements. Additional tests and inspections, at Contractor's expense, are performed to determine compliance of replaced or additional work with specified requirements. Prepare test and inspection reports. CLEANING AND PROTECTION Remove temporary protective coverings and strippable films, if any, as metal panels are installed, unless otherwise indicated in manufacturer's written installation instructions. On completion of metal panel installation, clean finished surfaces as recommended by metal panel manufacturer. Maintain in a clean condition during construction. After metal panel installation, clear weep holes and drainage channels of obstructions, dirt, and sealant. Replace metal panels that have been damaged or have deteriorated beyond successful repair by finish touchup or similar minor repair procedures. END OF SECTION 074213.13     Copyright 2018 AIA MasterSpec Full Length 12/18 (PM updated 08/20) PRODUCT MASTERSPEC LICENSED BY DELTEK, INC. TO BERRIDGE MANUFACTURING CO. FORMED METAL WALL PANELS074213.13 -  PAGE 1 ,-/3HV�   ' 9 V g � � � � ������Ŵ���r�i`WWNEE8h� EhO7�aJmH sH h� �h�9aJh�_vh�9aJhH�h�9aJh}h�9aJhb�h�9aJhKO=h+jm<�B*aJph�h�|h+jm<�B*aJph�!hH�h_�B* aJph�8sHtH$h�/�h_�5�B* aJph�8sHtH!h}h_�B* aJph�8sHtH$hb�h_�5�B* aJph�8sHtHh =�h�90J.aJh =�h�9aJh =�h�90J-aJhKO=h�9aJ-3�  ' 9 g � � � Q �  z � � o � F Y���������������������)�� $��*$a$gd+jm(��$d%d&d'dN��O��P��Q��gd_�� � � Q V �  V z � � V o � � � � � F V VYVv�Vz�OV�'V���Vu������������������������������������������������������yh6h_W�aJh =�h��aJh =�h�l?aJmH sH h =�h_W�aJh =�h�k�aJmH sH hKO=h_W�aJhKO=h�9aJh�|h��aJh{[h��aJh{[h�95�aJh{[h�9aJh�%�h�9aJh�q8h�9aJh�Mh�9aJ/Yv�z�O�'��Vu�Sb=��}�P������������������������)��gdNgdNgdN��gd�H�)gd_W���)gdKO=l�)��X?�RSVb�=V���������./QUV}�PV�� V���������ƻ������x�o��ffffff[Pfh{[h�90J/aJh{[h�90J0aJh{[h�9aJh{[h_W�aJh{[h{&aJh{[hNaJh�%�hNaJh�%�h�h�aJh�q8h�9aJh�Mh�90J/aJh hN0J/aJh� �h�90J/aJh� �h�90J0aJh� �hN0J0aJh�_vh�9aJhH�h�9aJh}h�9aJhb�h�H�aJ��x��p������);K�a �� M!�!�"�"X#������������������������gd =���gd =�gd =�))gdKO=l�)��X?��Vx�V��Vp����V����);KVV�Va������� V�) , 6 A D �������������ƽ���������������������xneh� �h�9aJh� �h�95�aJh�_vhO7�5�aJh�_vh�95�aJh}h�{aJmH sH hG=Lh =�aJh�_vh�9aJhH�h�9aJh}h�9aJhb�h�9aJh =�h�9aJhKO=hO7�aJmH sH hKO=h�9aJh�|h�aJh{[h�aJh{[h�9aJ'D O V ] d g o � !!!!%K%�������Ǿ��Ǭ�����������ri\iShH�h�9aJh�/�h�$\aJmH sH h�/�h�9aJh}hC�aJmH sH h}h�9aJhb�h�9aJh =�h�9aJhKO=h�9aJh�|h�9aJh�K�h�$aJh�%�h�$aJh�%�h�aJh�%�h�9aJh�Mh�9aJh� Eh�95�aJh h�9aJh� �h�9aJh� �h�95�aJX#�#%�%�%�&�&l'u'7(�())a)�)�)�* +]+�+�+=,F,_,�-(.�.�������������������������)$a$gd��gd�6�)gd�H�gd_W�����)K%L%V%s%x%�%�%�%�%O&V&a&�&�&V'l'u'�'�'7(?(S(V(](^(�())T)V)_)a)�)�)�)�)�)�)�������¹��������������w�nneenn\enenh{[h�u�aJh{[hC�aJh{[h�9aJh�K�h�0�aJmH sH h�K�hC�aJmH sH h�K�h�9aJh�%�h_�aJmH sH h�%�h�9aJh�q8h1C�aJh� Eh�9aJh h�9aJh� �h�9aJh� �h�$\aJh�_vh�>aJmH sH h�_vh�$\aJh�_vh�$\aJmH sH $�)**V*�*�* +%+++>+P+]+|+�+�+�+�+�+�+�+=,F,M,_,M-�-...'.(.����������������������Ɂ�xobYPh�%�h�HaJh�q8h�H�aJh�MhC�aJmH sH h� Eh�H�aJh� �h�H�aJh�_vh�H�aJh =�h�9aJh�%�h�9aJh�Mh�9aJh� EhC�aJh� �h�9aJh�_vh1C�aJh�_vh�9aJhH�h�9aJh�/�h1C�aJh�/�h�9aJ h�/�aJh{[h�0�aJmH sH h{[h�9aJ(.M.U.V.].a.c.f.l.o.p.�.�.�.�.�.�.�.M/k/}/�/�/���������ŷ��l_VMMDM;h6h�9aJh =�h1C�aJh =�h�9aJhKO=hC�aJh�|hO7�aJmH sH $jhKO=h�}S<�UaJmH sH hKO=h�}S0J:aJmH sH $jhH�h�}S<�UaJmH sH *�jhH�h3j�<�UaJmH sH hH�h3j�<�aJmH sH $jh�|h�}S<�UaJmH sH h�%�h_�aJh�%�hC�aJh�%�h�5�aJmH sH h�%�h�5�aJ�.�/�/�/%0>1�1y23�3>4J5�5�5�5J6�6 7,7C7�8 :���������������������)gdQtxgdQtx)gd�e�gd�Z���gd�Z���gd�H�)gd.���gd�.I)gd��)���/�/�/�/%0m0>1X1�1�1�1�1�1�1222222y2�2�2�23b3{3|3~3�3�3�3�����������ܳ��ܪ��ܗ����xoxf]Th�/�h�w�aJh�|h�$\aJho}xh�$\aJh{[hfa�aJh{[h.�aJh{[h�w�aJh{[h��aJmH sH h{[h��aJh{[hnQ5�aJh{[hnQaJh{[hnQaJmH sH h{[h�95�aJh =�h�9aJhKO=h�9aJh{[h�9aJh� �h�9aJh�_vh�9aJh�/�h�9aJ�3�3�3 4 4 4444 4,4>4[4\4e4�4�4�4�4�4�4�4�4�4�4J5\5^5e5h5r5u55�5�5�5�5�5�������������������‰}}q�}q��h_h{[h�Z�aJh{[h�K;aJh{[hN 0J/5�aJh{[hN 0J05�aJh{[hN aJh{[h.�0J/5�aJh{[h.�0J05�aJh{[h�90J/5�aJh{[h�90J05�aJh{[h�9aJh{[h�f�aJh{[h_ aJmH sH h{[h�f�aJmH sH h{[h.�aJhH�h�w�aJ%�5�5�5�5�5�5�5�5�5�5�5�5666,6.6/6G6H6I6J6R6}6�6�6��������Ǿ�������yj]TKAKAh =�h�95�aJh =�h�9aJhKO=h�e�aJh�|h�f�aJmH sH jhKO=h�M<�UaJhKO=h�M0J:aJjhH�h�M<�UaJhH�h�MaJhH�h�M<�aJjh�|h�M<�UaJh{[h�MaJh{[h�e�aJh{[h� |aJh{[h�f�aJh{[h�95�aJh{[h�9aJh{[h�Z�aJho}xh�Z�\�aJ�6�6�6�6�6�6�6�6�6�6�6777 7 7 777"7$7'7*7,7C7J7�����ȿ����������wlaVa�MMh{[hQtxaJh�K�hh�0J/aJh�K�h�90J/aJh�K�h�90J0aJh�K�hh�0J0aJh�K�h�9aJh�%�h�Y�aJho}xh�Y�\�aJho}xh�90J/\�aJho}xh�90J0\�aJh� �h�9aJhH�h�9aJh�/�h�9aJh�/�h�95�aJh}h�9aJhb�h�9aJh� h�95�aJh6h�9aJJ7�7�7�7�7�7�7838C8v8z8�8�8�8B9C9R9�9 : :C:S:X:Y:�:�: ;;;;C;�;�;�;4<����������������������˾�����zzzod[hb�hQtxaJhb�hQtx0J/aJh� hQtx0J0aJh =�hQtxaJhKO=hQtxaJjh =�h�"zUaJh =�h�"z0J:aJmH sH jhH�h�"zUaJhH�h�"zaJjhKO=h�"zUaJh{[h�"zaJh{[hQtxaJmH sH h{[hQtxaJh{[h�i�aJh{[h�i�aJmH sH # :;s<=y=�=�=�=>]>{>�>%?�?�?@p@�A|B�CDD�����������������������))gd_W�)gdQtxgdQtx��gdQtx@& gdQtxgdQtx��gdQtx��@& gdQtxgdQtx)gd��4<C<s<�<�<�<=%=4=C=y=�=�=�=�=�=�=�=�=�=�=�=�=�=�=������ƽ�ƴ������wne\SJAh�X hQtxaJh�X h=z�aJh� �hQtxaJh� �h_ aJhH�hQtxaJh�/�hQtxaJh�/�h=z�aJh}h_ aJhb�hQtxaJ h� h=z�0J;>*B*aJph� h =�hQtx0J;>*B*aJph�h =�h_ aJhKO=hQtxaJh =�hQtxaJh� �h��aJh� �h�"�aJmH sH hH�h��aJh�/�h��aJh}hQtxaJ�=�=> >>>>+>C>S>[>\>]>^>q>r>x>{>�>�>�>�>?? ??%?C?�?�?�?@@@&@0@1@�������������������{����{�rrer\\r\reh{[h�9aJh{[hQtxaJmH sH h{[hQtxaJh�K�hQtx0J/aJh�K�hQtx0J0aJh�K�hQtxaJh�K�hQtx5�aJh�K�hO7�5�aJh�%�hQtx5�aJh�%�h=z�aJh�%�hQtxaJh�q8hQtxaJh�r�h_ aJh�MhQtxaJh� Eh=z�aJh� EhQtxaJh h_ aJ$1@>@?@@@C@O@V@W@`@a@p@�@�@�@�@�@AA(A2AAACA�ABCB|BCCC�CDDCDDEE EECE�EFCFGCGQGaG�G�G�G�G�G�GHCH�H�H�H�����������ɾ�����ɾ��������������ɾ�������ᝐ��������h{[h�uaJmH sH h{[h�x1aJmH sH h{[h� |aJh{[h� |0J/aJh{[h�90J/aJh{[h�90J0aJh{[hQtxaJmH sH h{[h�9aJh{[h�(FaJmH sH h{[hQtxaJ7D�EQG�H�I-JKLGLSLzM�M�N�OJP�PSQ�Q�R5S>S�SIUgU�VY�[����������������������������gd�g�)����)$a$gd���H�H�H�H�H�H�HI;I=I>ICI�I�I�I�I�I�I�IJJ-JCJ�J�J�J��������ѹ�����|of]]|||RGh� h�90J/aJh =�h�90J0aJhKO=h�9aJh� h�9aJh =�hAm�aJmH sH h =�h�9aJh =�hQtxaJmH sH hKO=hQtxaJmH sH jh =�h�g�<�UaJh =�h�g�0J:aJjhH�h�g�<�UaJhH�h�g�aJhH�h�g�<�aJjhKO=h�g�<�UaJh{[h�g�aJh{[h�g�aJmH sH �JKK KKK0KCKhKLLCLGLSLgLMCMgMzM�MNCNXN�NO4O5O SCS�STCT�T�TUCUIUgUnU{U|U�U�U�U�U�UV�������������������������v�v�i`Sh�K�h�f�aJmH sH h�K�h�9aJh�K�h�i�aJmH sH h�%�h��aJmH sH h�%�h�i�aJmH sH h�q8h�9aJh�Mh�9aJh� Eh�9aJh� EhmsaJmH sH hh�9aJh�X h�9aJh� �h�9aJhH�h�9aJh�/�hU`aJh�/�h�9aJhb�h�9aJh� h�9aJ VVCV�VWWCWwW{W|WW�W�W�W�W�W�W�W�W�W�W�W�W�W�W�W�WX#X+X7X8XCXGXOXZX�X�X�XYYY*Y��������������ͻ�������Ͱ����ͧ���͞���yp�hb�h�9aJh� hN�aJh =�hN�5�aJh =�hN�aJh =�h�9aJhKO=h�9aJh�K�h�i�aJh�K�hXB0J/aJh�K�hCztaJh�K�hDj aJh�K�h�i60J/aJh�K�hXB0J0aJh�K�h�i60J0aJh�K�h�i6aJh�K�h�9aJ**Y-YCY�Y�YZZZZZ)Z*Z9ZAZCZMZNZTZ[ZgZvZzZ{Z~Z�Z�Z�Z�Z�Z�Z�Z�Z�Z�Z[C[P[}[~[�[���������Ļ���Ļ�������İ���Ļ������vlh =�h�D�5�aJh =�h�D�aJh =�h�9aJhKO=h�9aJh{[h�i60J/aJh{[h�i60J0aJh{[h�i6aJh�K�hR0J/aJh�K�hRaJh�K�h�i60J/aJh�K�hR0J0aJh�K�h�i60J0aJh�K�h�i6aJh�K�h�9aJh�K�h�0�aJ'�[�[�[\\C\�\�\�\�\�\�\�\�\]]]+],]C]G]H]S]T]�]�]^B^C^v^z^��������ѻ������������wnannnnWh�MaJmH sH h�K�h0B1aJmH sH h�K�h�9aJh�K�h�aJmH sH h�%�h��aJmH sH h�%�h�aJmH sH h�q8h�9aJh�Mh�9aJh�Mh�0�0J/aJh�Mh�90J/aJh�Mh�0�0J0aJh�Mh�90J0aJh� Eh�9aJh h�9aJhb�h�9aJh� h�D�aJ�[\�\]B^�^?a�c�c�c�d�d�e~fg�ghh�h�h�i�i�jYk9lfl�l�l��������������������������������gd��)z^{^�^_C_F_�_�_�_�_�_�_�_�_�_�_�_�_``````` `#`C`Z`b`n`o`~`�`�`����������������{p��{e{pZp��{p��{ph�K�hin0J/aJh�K�hin0J0aJh�K�h�i60J/aJh�K�h�i60J0aJh�K�h�i6aJh�K�hinaJh�%�h�i60J0aJh�%�h�i6aJh�%�hinaJh�%�h�i60J/aJh�q8h�i60J0aJh�Mhin0J0aJh�Mh�i60J0aJh�Mh�i6aJh�Mh�9aJh�Mh�x1aJmH sH "�`aaa t�t�t�u�u�v-w�w6y|z{9}O}%~���������������������������)gdZux)��0nCn{n�n�n�n�n�noo2o;o t���������������������~�����u�lllllllllh{[h�9aJh�K�hZuxaJh�K�h��aJmH sH h�K�h�9aJh�K�h�i aJh�K�h�z$aJh�%�h�i aJh�%�h�9aJh�q8h�9aJh�r�h�9aJh� Eh�i aJh h�9aJhA~h�i aJh�X h�9aJh� �h�9aJhH�h�9aJ&>tCt�t�tuCu�u�uv(v.v7vCv�v�v�v�vw*w-wCw�wxCxy6yCyzCz|z{C{{�{�{�{||"|+|4|C|�|�|�|}9}C}O}�}�}�}~%~6~C~G~J~P~�~��������������������������������������������������������hb�h�95�aJhb�h�9aJhb�hb�aJhb�aJmH sH h{[h�W�0J0aJh{[h�95�aJh{[h�90J/aJh{[h�90J0aJh{[h�9aJh{[hZuxaJ;%~�~�B�߀��q�܂l�������������������ԃ�� �9�P��������������������������1$If$If$a$gd�$\gd�$\')�~C��B�C�߀���C��C�q�܂�C�l�������������������������������������������������΃σԃ������ �8�9��������������������������������������ýɹ����������ɐ� h�Z�0J. h�h�$\h�$\ hs#^0J, h�$\0J, h�L�0J, h�Z�0J,h�L� h+jm0J+ h�Z�0J+h�Z� h�L�0J* h�Z�0J*h=�jh=�Uh�K�h�9aJh�%�h�9aJh�q8h�9aJ69�B�C�E�F�L�M�N�O�P�Q�R�S�T��������������h�K�h�9aJh=�hs#^mHnHujh�Z�Uh�Z� h�Z�0J- P�Q�R�S�T�����'Ekd�$$If�A�0����$�P�������������4� Aa�/<0BP��/ ��=!��"��#��$��%����� ���D���y������K� ���y������K� �https://www.berridge.com/resources/testing-summary-chart/yX��;H�,�]ą'c��V$$If�!vh#v�#vP:V �A��5��5�P4�4� AKx���������666666666vvvvvvvvv666666>666666666666666666666666666�6666666666�666666666666hH66666666666666666666666666666666666666666666666666666666666666666�62���� 0@P`p������2(�� 0@P`p������ 0@P`p������ 0@P`p������ 0@P`p������ 0@P`p������ 0@P`p��8X�V~�������� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@66666_HmH nH sH tH <`��< NormalCJ_HmH sH tH DA`���D Default Paragraph FontVi@���V 0 Table Normal :V �4�4� la� (k ���( 0No List 6�O�6 HDR$ ��$*$a$4�O4 FTR$ ��$*$a$0�O"0 SCT$��*$a$<�OR< PRT$$ & F��*$@&a$:�b: SUT$ & F��*$@&a$:�b: DST$ & F��*$@&a$D�ObD ART$$$ & F �`��*$@&a$N�ObN @PR1!$ & F �`��*$@&a$ mHsHtH>�Or> JPR2$ & F ��*$@&a$>�O�> PR3$ & F ��*$@&a$>��> PR4$ & F � *$@&a$>��> PR5$ & F �` *$@&a$8�b8 TB1$� ��*$^� a$8�r8 TB2$�`��*$^�`a$8��8 TB3$����*$^��a$8��8 TB4$����*$^��a$8��8 TB5$� ��*$^� a$8��8 TF1 $� ��*$^� a$8��8 TF2!$�`��*$^�`a$8��8 TF3"$����*$^��a$8��8 TF4#$����*$^��a$8��8 TF5$$� ��*$^� a$&�R& TCH%*$6�b6 TCE&���p�*$^��`�p�0�Or0 EOS'$��*$a$@��@ ANT($��*$a$<�>*B* ph��H�O�H 7PV�CMT)$��*$a$<�B*mHph�sHtH�O�� CPR�O�� SPN�O�� SPD�O�� NUM�O�� NAM �o��� SIB* �o�� IPB*,�O, RJUST1$a$4"4 3zL10Header 2 �H�$.��1. 2zL10 Header Char4 B4 5zL10Footer 4 �H�$.��Q. 4zL10 Footer Char��b� 8xTIPJ6��$d%d&d'dN��O��P��Q��B* CJmHph�8sHtHD�/��qD )PV�CMT Char<�B*CJmHph�sHtH4�/���4 6xTIP Char <�B* ph�8>�/���> Or� SustHyperlink >*B* ph�6U`���6 Or�0 Hyperlink >*B*ph�:�o���: �@� SAhyperlink >*B*ph�l ���� w]�PM_CMTd<$��$d!%d$&d!'d$*$-D�M� ����N��!O��$P��!Q��$a$ B*aJph�P��P >�h�0 Balloon Text=CJOJQJaJmHsHtHN�/���N =�h�0Balloon Text CharCJOJQJ^JaJ���� A�F�PRNo? �`�`���$d!%d$&d!'d$-DM� �����N��!O��$P��!Q��$^�``��� mHsHtH,�/��, �F�PR1 CharCJJ�/��J ?�F�PRN Char!CJfHmHq� �����sHtHRv!��!R N0Unresolved MentionB*ph���q� ����B' ��1B _W�0Comment ReferenceCJaJ8B8 E_W�0 Comment TextDCJ:��Q: D_W�0Comment Text Char@� ��b@��0RevisionFCJ_HmH sH tH @jAB@ H"0Comment SubjectG5�\�F�/���F G"0Comment Subject Char5�\�FV ���F QR�0FollowedHyperlink >*B*ph�Or,�/���,  =�PR2 CharCJPK!����[Content_Types].xml���N�0E�H���-J��@%�ǎǢ|�ș$�ز�U��L�TB� l,�3��;�r��Ø��J��B+$�G]��7O٭V�� �j\�{�c�p/�ID��g�6wZ���0s�������=D�ĵw %��;�r,q�lEآyDQ"Q�,=�c�8�B,��!g�����xMD�&铁M��.��/SA�e���^�Qש���F½���|Sˌ��D�إ��bj|��E�7�C�<bʼN��p�r8����f�nߧ��FrI�.�{�1�f�V��ԅ�$2���1�(�t���}��k�JV��1���/�� Ú��Q�L�×�0��7�#�]�f��V�����Ih�����c���M�Z6/Hߏ ��bW`�Gv��� �Ts��'���B��C����t!�LQ#�J�xݴyJ]� �C:��= ċ�(�t��R�Q�����;^����e�1�/�-��/A_Y�)�^���6(����p�[��_����&N��}�n���jzb�\�-�>��������������;n�V��b��*��.�7�p�]M��|�MMM�# ud9c��47=����iV��7�̪~㦓�ø�dfÕ��� �5j�� z��'^9�J{rJ�Ѓ�3A���x�| �F�U�9��…i�3��Q/B)L�ʾR���Px)04��N� O'�> �ag���YeH�j��*��k�b����lC=h�P�W!alf��p������X�� �O�AXl:X�V��Zb�r����� �Z�y4��S��w�3?��Wӊh��PxzSq]y T|����� ������� �VDK%�)(.�/�3�5�6J74<�=1@�H�J�PV*Y�[z^�`�c0n>t�~9�T�CEGIJLMNPQRSTVWXZ[\]^_abcefhiY�X#�. :D�[�l%~P�T�DFHKOUY`dgjo&�&�&...G.X2�2 3�@=A�AT|X��X��X��X������!���8�@�����������0�( � ��B �S ���� ?��� _Hlk511888568 _Hlk512950676 _Hlk518999889 _Hlt46911909 _Hlk492369724 _Hlk492370275 _Hlk492374083---�&�+�+�8U|@����&�+>,�8U|, 7 ^ i "%"�%�%�*�*- -,/8/�5�5�5�5�5666183848>8a8c8d8n8�8�8>=G=�>�>B B�B�B�B�B�H�H�M�MTU_U�{�{�{�{�{�{�{�{�{R|U|-23�'8���P�no��E' � � � V t u � S a � � }��O�����op����������(;J��a  �M��WX��L����ku6 7 � �!�"_$�%�%'&(&�&�&�'%(=)>)�)�)x*y*+�+=,�-I.,/B/C/�0�0 2 233r4s45%7�7�7�78o8p8�9�9{:|:�;�=P?Q?�@�@�A�A,BSDyEzE�E�E�F>K�K�KHMIMfMgM�N�P�PqS~S�ST�TUUAVBV�V YY�[�[�[�\�\�\^^~^_�_g`h`�`�`�a�a�b{f�f�gbhch�h�k=l>l�l�l�l�n,o-o�o6q{rOu$v%v�v�vww�w�wAxBx�x�xyypzqz�z�zk{�{�{�{�{�{�{�{�{�{R|U|333333���"�"=$=$F$F$�'�'�'�'>)>)�)�)~+~+�+�+�+�+�+�+�-�-�-�-�-�-�.�.�.�.//,/,/55%5%5QQ*Q*Q�Q�Q�Q�Q�S�S�T�TSUSU_U_U�U�UvVvV{V{V�V�V?Y?YbYbY�Y�Y�Y�Y�[�[:a:aSaSa~a~a�a�a�f�f�f�f2g2g )>)�)�)~+~+�+�+�+�+�+�+�-�-�-�-�-�-�.�.�.�.//,/,/55%5%5QQ*Q*Q�Q�Q�Q�Q�S�S�T�TSUSU_U_U�U�UvVvV{V{V�V�V?Y?YbYbY�Y�Y�Y�Y�[�[:a:aSaSa~a~a�a�a�f�f�f�f2g2g �Z�p}dPc ��{ }DA~�MN�`x�!�x��!N L= _ �!#�X#� $&$�z$�%�w%{&z'4f'y( (| )�)xM)�P)�A*�V*�W*�,�Y-�g-i0.OP.~|/s0�0�x0�10B1zL1�x1. 2S 3`C4�l4My4�65mJ5}6�-6�i6�N8�q8�9|^9p/:F:�K;�<KO=�3>�g>�l?&^@�w@XBYRC�CyBD� E�KE�xE�(F�H /H4`H�.I�ZI�sI�oJJ�xK0PL�TL�M�NeO�POOP�dP4ePjPnQGDQrQ�VR�S S�}S T�HT�"U&9U NU]V�V*VGX�XX�SYi1Z�FZ�sZ�[�$\K(\"^s#^{^Wx_� `�n`qa�Eaa&bXb�Zc:mc'zc�Hfmrf�khOLiv5j?^j�ekWl�rl+jm�,nin�ouo�Yo�HpMmpqr;Vr1lr#xr�ms�|s� t+,t�,tsttCzt^u�-u0/u�`u�Ov�_vxvQtxZuxo}x�"za#zGuz�{�G{� |�|�@|)J|�|�X}8t}^0~�u~<�Yao�&�� ��_��e�4f� �.F�Vj�����C��W�`u�Hy����f�&%�lV���?��K�|_�n-��1��Q��O��W��u�������O7��?��@�1C��w�g�r��Z��F��U��i��*�h��i�� �[$�N��{�gl�Or� S�?>� r�a��h�`i���s�:r����D�h��� f��0� �?��f��A��z�XA��i��v����"�J(��K��t����J��U�D[��q� d��a�3j�o��|���.�_K�&����$�h?�d�d}�R�K��H�J�Fr��v��7��r����5�k7� )�$/��O�QR�fa��d��w��y�m�`�V��l�4y�� �� ��/� 7� �u0��Y�R��%�]2�r��1��1��w��#��)��c�H�s:��L�J���[/��_��F��K�;\��i�� �� ����8�w]�=�eH��`��R��C�UY�� ��r��6�^����G�J�i�T��T�� ��T��Z�=z�b�n�y4�!,��Y��f�Am�� ��k�Q�;J��_�w�[�"�PV��2��y����g�je��8�ar��&�<�E+� =�_W�[]��p��h�KL����k�~-�/4��u��H�2��?��H�Y����0�4W��{�{�� DOIFormatMF04MF95MFOrigin SectionIDSpecTypeuserSustainabilityVar_30_1userSustainabilityVar_7_1Version03/01/1510742131307415MF04175 MasterSpec�30^userSustainabilityTopic_30_1^1,^<SustainabilityTopic id="30"><TopicText id="239"><RatingSystems><System id="1"/></RatingSystems> <Content><CMT>Retain "Recycled Content" Paragraph below to specify recycled content if required. An alternative method of requiring recycled content is to retain requirement in Project's Division�01 sustainable design requirements Section that gives Contractor the option and responsibility to determine how recycled content requirements will be met.</CMT><PR1>Recycled Content: Postconsumer recycled content plus one-half of preconsumer recycled content not less than &lt;Insert value&gt; percent.</PR1></Content> </TopicText></SustainabilityTopic>-7^userSustainabilityTopic_7_1^1,^<SustainabilityTopic id="7"><TopicText id="168"><RatingSystems><System id="1"/></RatingSystems> <Content><PR2>Product Data: For recycled content, indicating postconsumer and preconsumer recycled content and cost.</PR2></Content> </TopicText></SustainabilityTopic>11743�@�,/,/,/,/T|�@��Unknown������������G��.�[x� �Times New Roman5��Symbol3.� �.�[x� �Arial5.� �.�[`�)�TahomaC.,�.�{$� �Calibri Light7.��.�{$� �CalibriA����$B�Cambria Math"���h�h2,�g̈G%oi ?�oi ?�!��F{F{K�q������XZ �� $P����������������������zL1 !xx����2 ���,SECTION 074213.13 - FORMED METAL WALL PANELSFORMED METAL WALL PANELSBAS-12345-MS80 ARCOM, Inc. Lisa Reimert �� �����Oh��+'��0����� ,< T` � � ������0SECTION 074213.13 - FORMED METAL WALL PANELSFORMED METAL WALL PANELS ARCOM, Inc.BAS-12345-MS80NormalLisa Reimert8Microsoft Office Word@9+@��]rk�@'{� oi�� ��՜.��+,��D��՜.��+,��p, px����� ���� � � MicrosoftB�?F{ -SECTION 074213.13 - FORMED METAL WALL PANELS Title0 8@ _PID_HLINKS�A�)* Whttp://www.berridge.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf)*Whttp://www.berridge.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf5( http://www.berridge.com/colors/ M:https://www.berridge.com/resources/testing-summary-chart/  !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijk����mnopqrs����uvwxyz{|}~������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������Root Entry�������� �F�#�'{��@Data ������������l1Table��������t�MWordDocument ����1�SummaryInformation(�������������DocumentSummaryInformation8���������MsoDataStore���������V�'{����'{�M��C4�M�Z��A�50I�0M��A==2���������V�'{����'{�Item ���� ����2Properties������������UCompObj���� r���������������� ���� �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� �� ���� �F Microsoft Word 97-2003 Document MSWordDocWord.Document.8�9�q