��ࡱ�>�� V�bjbj~~ 1�{{�� 8M �� l @�E!E"["["["�#�$,�$�?�?�?�?�?�?�?,�A�oD*�? �$�#�#�$�$�?�& ["["4�?�&�&�&�$N [" ["�.��&�$�?�&�&:d+�,��z��)&��+ �.�?0@�+ �E�&�E,�& ,��$�$�$�?�?�&�$�$�$@�$�$�$�$��E�$�$�$�$�$�$�$�$�$�+ �: SECTION 074113.16 - STANDING-SEAM METAL ROOF PANELS TIPS: To view non-printing Editor's Notes that provide guidance for editing, click on Masterworks/Single-File Formatting/Toggle/Editor's Notes. Revise this Section by deleting and inserting text to meet Project-specific requirements. This Section uses the term "Architect." Change this term to match that used to identify the design professional as defined in the General and Supplementary Conditions. GENERAL RELATED DOCUMENTS Retain or delete this article in all Sections of Project Manual. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division�01 Specification Sections, apply to this Section. SUMMARY Section includes standing-seam metal roof panels. Related Sections: Retain subparagraphs below to cross-reference requirements Contractor might expect to find in this Section but are specified in other Sections. Section�074293 "Soffit Panels" for metal panels used in horizontal soffit applications. Section�077253 "Snow Guards" for prefabricated devices designed to hold snow on the roof surface, allowing it to melt and drain off slowly. PREINSTALLATION MEETINGS Retain "Preinstallation Conference" Paragraph below if Work of this Section is extensive or complex enough to justify a conference. Preinstallation Conference: Conduct conference at [Project site] ．如果需要，插入13100节“项目管理和协调”中没有提到的与会者名单。如有需要，保留以下分段;修改为包含更具体的会议信息。与船东、建筑师、船东保险公司(如适用)、金属面板安装商、金属面板制造商代表、结构支撑安装商以及与金属面板有接口或影响的安装商会面，包括屋顶附件和屋顶安装设备的安装商。审查并确定施工进度，确认材料、安装人员、设备和设施的可用性，以确保施工进度和避免延误。审查与金属面板安装相关的方法和程序，包括制造商的书面说明。检查支撑条件是否符合要求，包括结构构件之间的对齐和连接。在屋顶覆盖期间和之后，检查甲板的结构荷载限制。检查闪光，特殊细节，排水，渗透，设备限制，以及其他影响金属面板的建筑状况。 Review governing regulations and requirements for insurance, certificates, and tests and inspections if applicable. Review temporary protection requirements for metal panel systems during and after installation. Review procedures for repair of metal panels damaged after installation. Document proceedings, including corrective measures and actions required, and furnish copy of record to each participant. ACTION SUBMITTALS Product Data: For each type of product. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for each type of panel and accessory. Sustainable Design Submittals: HYPERLINK "http://www.arcomnet.com/sustainable_design.aspx?topic=6"Product Test Reports: For roof materials, documentation indicating that roof materials comply with Solar Reflectance Index requirements. HYPERLINK "http://www.arcomnet.com/sustainable_design.aspx?topic=7"Product Data: For recycled content, indicating postconsumer and preconsumer recycled content and cost. Shop Drawings: Include fabrication and installation layouts of metal panels; details of edge conditions, joints, panel profiles, corners, anchorages, attachment system, trim, flashings, closures, and accessories; and special details. Accessories: Include details of the flashing, trim, and anchorage systems, at a scale of not less than 3" = 1'-0" (1:5). Calculations: Include calculations with registered engineer seal, verifying roof panel and attachment method resist wind pressures imposed on it pursuant to applicable building codes. Retain "Samples for Initial Selection" and "Samples for Verification" paragraphs for two-stage Samples. Samples for Initial Selection: For each type of metal panel indicated with factory-applied color finishes. Include similar Samples of trim and accessories involving color selection. Samples for Verification: For each type of exposed finish required, prepared on Samples of size indicated below. Metal Panels: 12 inches (305 mm) long by actual panel width. Include clips, fasteners, closures, and other metal panel accessories. INFORMATIONAL SUBMITTALS Coordinate "Qualification Data" Paragraph below with qualification requirements in Section�014000 "Quality Requirements" and as may be supplemented in "Quality Assurance" Article. Qualification Data: For Installer and Manufacturer. Product Test Reports: For each product, for tests performed by a qualified testing agency. Field quality-control reports. Sample Warranties: For special warranties. CLOSEOUT SUBMITTALS Maintenance Data: For metal panels to include in maintenance manuals. QUALITY ASSURANCE Installer Qualifications: An entity that employs installers and supervisors who are trained and approved by manufacturer. Manufacturer Qualifications: Company specializing in Architectural Sheet Metal Products. Mockups: Build mockups to verify selections made under Sample submittals and to demonstrate aesthetic effects and set quality standards for fabrication and installation. Retain first subparagraph below for large-scale mockup. Indicate portion of roof represented by mockup on Drawings or draw mockup as separate element. Build mockup of typical roof area and eave[,�including fascia,] [and soffit] as shown on Drawings; approximately 48 inches (1200 mm) square by full thickness, including attachments[,�underlayment,] and accessories. Retain first subparagraph below for limited mockups. Build mockups for typical roof area only, including accessories. Size: 4 ft (1200 mm) long by 4 ft (1200 mm) high. [Each type of exposed seam and seam termination] ．除非架构师专门以书面形式批准此类偏差，否则模型批准的批准并不构成样机中所载的合同文件的批准。在下面保留分段，如果意图是在裁员和删除模型中的第14000个“质量要求”中的默认要求。如果在实质性完成时，批准的样机可能成为已完成工作的一部分。交付，储存和处理提供部件，金属面板和其他制造的物品，以免损坏或变形。包装金属面板，用于运输和处理过程中的保护。以防止弯曲，翘曲，扭曲和表面损坏的方式卸载，储存和竖立金属板。在平台或托盘上水平堆叠金属面板，覆盖着合适的风雨壁特和通风覆盖物。储存金属面板以确保干燥，水坡度为水排水。请勿将金属面板存储在与可能导致染色，牙齿或其他表面损坏的其他材料接触。 Remove strippable protective covering on metal panels as panels are being installed. Do not leave the film on installed panels. FIELD CONDITIONS Weather Limitations: Proceed with installation only when existing and forecasted weather conditions permit assembly of metal panels to be performed according to manufacturers' written instructions and warranty requirements. COORDINATION Coordinate sizes and locations of roof curbs, equipment supports, and roof penetrations with actual equipment provided. Coordinate metal panel installation with rain drainage work, flashing, trim, construction of soffits, and other adjoining work to provide a leakproof, secure, and noncorrosive installation. WARRANTY When warranties are required, verify with Owner's counsel that special warranties stated in this article are not less than remedies available to Owner under prevailing local laws. Galvalume Substrate Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of metal panel systems that fail in materials or workmanship within specified warranty period. Failures include, but are not limited to, the following: Structural failures including rupturing or perforating. Deterioration of metals and other materials beyond normal weathering. Warranty Period: 20 years and 6 months from date of Substantial Completion. Special Warranty on Panel Finishes: Manufacturer's standard form in which manufacturer agrees to repair finish or replace metal panels that show evidence of deterioration of factory-applied finishes within specified warranty period. Usually retain "Exposed Panel Finish" Subparagraph below for fluoropolymer finishes; verify availability with manufacturer. Exposed Panel Finish: Deterioration includes, but is not limited to, the following: Color fading more than 5�Hunter units when tested according to ASTM�D�2244. Chalking in excess of a No.�8 rating when tested according to ASTM�D�4214. Cracking, chipping, peeling, or failure of paint to adhere to bare metal. Finish Warranty Period: 20 years from date of Substantial Completion. Verify availability of warranty in "Special Weathertightness Warranty" Paragraph below; only a few manufacturers, for a limited number of products, offer a weathertightness warranty. Special Watertightness Warranty: Manufacturer's [standard form] [no dollar limit form] in which manufacturer agrees to repair or replace standing-seam metal roof panel assemblies that fail to remain watertight, including leaks, within specified warranty period. Verify available warranties and warranty periods for units and components made by manufacturers listed in Part�2 articles. Warranty Period: [20] [15] [10] [5] [2] years from date of Substantial Completion. Shop drawings must be provided (or reviewed) by the panel manufacturer and approved by the panel manufacturer prior to the installation of the panel system. A minimum of two inspections by the technical representative of the panel system manufacturer are required. The first inspection is to be performed when the underlayment and flashing are in place and the second inspection is to be performed when the roof is complete. Installer Warranty Required when requiring �Special Watertightness Warranty� reflected above. Special Installer Warranty: Furnish a written warranty signed by the Panel Applicator for a two year period from the date of substantial completion of the building guaranteeing materials and workmanship for watertightness of the roofing system, flashings, penetrations, and against all leaks. PRODUCTS PERFORMANCE REQUIREMENTS Retain "Recycled Content" Paragraph below to specify recycled content if required. An alternative method of requiring recycled content is to retain requirement in Project's Division�01 sustainable design requirements Section that gives Contractor the option and responsibility to determine how recycled content requirements will be met. HYPERLINK "http://www.arcomnet.com/sustainable_design.aspx?topic=30"Recycled Content: Postconsumer recycled content plus one-half of preconsumer recycled content not less than 29 percent. "Solar Reflectance Index" Paragraph below applies to LEED 2009. First option is minimum for roofs with slopes of 2:12 or less; second option is for roofs with slopes steeper than 2:12. HYPERLINK "http://www.arcomnet.com/sustainable_design.aspx?topic=27"Solar Reflectance Index: Not less than [78] [29] when calculated according to ASTM�E�1980, based on testing identical products by a qualified testing agency. Retain first "Energy Performance" Paragraph below for roofs that must comply with the EPA/DOE's ENERGY STAR requirements. The EPA/DOE's ENERGY STAR "Roof Product List" is available in PDF at www.energystar.gov. Energy Performance: Provide roof panels that are listed on the EPA/DOE's ENERGY STAR "Roof Product List" for [low] [steep]-slope roof products. Retain "Energy Performance" Paragraph below for roofs that must comply with local "cool-roof" energy legislation; verify requirements with authorities having jurisdiction. Example and options below are for low-slope roofs that must comply with prescriptive approach of CCR Title�24 (California Building Standards Code). Energy Performance: Provide roof panels according to one of the following when tested according to CRRC-1: Three-year, aged solar reflectance of not less than [0.55] 发射率不小于[0.75] ．Three-year, aged Solar Reflectance Index of not less than [64] 当根据ASTM E 1980计算时。结构性能:根据UL580的测试，提供能够承受以下荷载影响的金属面板系统:风荷载:如图纸所示。挠度限制:对于风荷载，不大于[1/180][1/240] 的跨度。对于ASTM E 1680, E283, E1646和E331测试报告，请访问//www.efxbank.com/technical/astm-air-water-infiltration-reports/。漏气:漏气不大于0.8 cfm/sq。测试压力差:6.24 lbf/sq. h，测试压力差:6.24 lbf/sq. h，测试压力差:6.24 lbf/sq. h，测试压力差:6.24 lbf/sq. h，测试压力差:6.24 lbf/sq. h，测试压力差:6.24 lbf/sq. h，测试压力差:6.24 lbf/sq. h。英尺(300 Pa)。静压下的水渗透性:根据ASTM�E 1646和ASTM�E 331的测试，在以下测试压力差下没有水渗透性:测试压力差:8 lbf/sq。英尺(383.04 Pa)。如果需要ul级屋顶，保留下面的“抗风压”段落。确认产品在UL的“屋面材料和系统目录”中。UL清单包括对整个组件的要求，而不仅仅是金属屋面板。 Wind-Uplift Resistance: Provide metal roof panel assemblies that comply with UL�580 for wind-uplift-resistance class indicated. Uplift Rating: UL�90. Thermal Movements: Allow for thermal movements from ambient and surface temperature changes by preventing buckling, opening of joints, overstressing of components, failure of joint sealants, failure of connections, and other detrimental effects. Base calculations on surface temperatures of materials due to both solar heat gain and nighttime-sky heat loss. Differential values (for aluminum in particular) in "Temperature Change (Range)" Subparagraph below are suitable for most of the U.S.; revise to suit Project. Temperature Change (Range): [120 deg�F (67 deg�C), ambient; 180 deg�F (100 deg�C), material surfaces] ．立式接缝金属屋面板通用:提供工厂成型的金属屋面板，其安装方式是将相邻面板的凸起边重叠并相互连接，并在侧搭接中使用隐藏夹将面板机械连接到支架上。包括防风雨安装所需的夹子、夹板、压板和附件。为每一个需要的产品插入图纸名称。使用图纸上的这些名称来识别每个产品。垂直肋，板条接缝，站立缝金属屋顶板 :在面板边缘有垂直的肋，肋之间有[面板条纹][平底锅];设计用于机械连接面板到支架使用隐藏的夹位于面板的一侧，对齐垂直肋骨和扣在板条缝帽的连续安装。 HYPERLINK“http://www.specagent.com/Lookup?ulid=6906”设计基础产品:根据要求，提供 HYPERLINK“http://www.specagent.com/Lookup?uid=123457046510”贝里奇制造公司;[t - panel][高接缝t - panel]或类似产品，由以下任一产品提供: ．金属涂层钢板:符合ASTM�A�792/A�792M, Class AZ50 (Class AZM150)涂层指定的铝锌合金涂层钢板;结构质量。采用卷涂工艺进行预涂，符合ASTM�A�755/A�755M要求。在指定之前，确认0.029英寸厚的Tee-panel的可用性，因为它的可用性有限，可能需要更长的交货时间。公称厚度:[0.024英寸(0.61 mm)][0.029英寸(0.74 mm)]外饰面:[双涂层氟聚合物][云母氟聚合物][金属氟聚合物]。涂漆材料应该有一个可移动的塑料薄膜，以保护在滚成型，运输和处理期间的油漆。安装面板之前，必须将可拆卸(保护膜)拆除。参考颜色表位于: HYPERLINK "//www.efxbank.com/colors/" //www.efxbank.com/colors/的选项。颜色:[根据制造商的指定][匹配建筑师的样品][由建筑师从制造商的全系列中选择] ．铝板:卷涂板，ASTM�B�209 (ASTM�B�209M)， 3105合金，H14回火，以适应成型操作和结构性能的要求。在指定前确认Tee-panel的可用性，因为它的可用性有限，可能会有较长的交付时间。厚度:0.032英寸(0.81毫米)。表面:光滑、平整。外饰面:[双涂层氟聚合物][云母氟聚合物][金属氟聚合物]。参考颜色表位于: HYPERLINK "//www.efxbank.com/colors/" //www.efxbank.com/colors/的选项。颜色:[根据制造商的指定][匹配建筑师的样品][由建筑师从制造商的全系列中选择] ．Utilize the Folding Tee-Clip listed below when required by the installation instructions located at HYPERLINK "//www.efxbank.com/wp-content/uploads/2013/03/Berridge-Tee-Panel-Installation-Details.pdf" //www.efxbank.com/wp-content/uploads/2013/03/Berridge-Tee-Panel-Installation-Details.pdf or when a curved roof is present.When utilizing the Folding Tee-Clip, assure the thickness of the clip is 0.0149 inch (0.37846 mm).Clips: [Tee-Clip] [Folding Tee-Clip] to accommodate thermal movement.Retain one of two "Material" subparagraphs below.Retain steel clips for metallic-coated steel roof panels and stainless-steel clips for aluminum.Material: [0.024-inch- (0.61-mm-)] [0.0149-inch- (0.37846-mm-)] nominal thickness, aluminum-zinc alloy-coated steel sheet.Material: 0.025-inch- (0.64-mm-) thick, stainless-steel sheet.Panel Coverage: [12.75 inches (323.85 mm)] [18.25 inches (463.55 mm)].Panel Height: [1.5 inches (38 mm)] [1.0 inches (51 mm)]. UNDERLAYMENT MATERIALS Retain appropriate paragraphs in this article for metal roof panels applied over sheathing. Self-adhering, high-temperature underlayment may be applied only at eaves, valleys, and other areas vulnerable to leakage, with felt applied over the remainder of the roof; or underlayment may be applied over the entire roof area. Underlayments listed in "Self-Adhering, High-Temperature Underlayment" Paragraph below are suitable for higher temperatures associated with metal roofing. Revise if high-temperature underlayments are not required. Verify, with underlayment manufacturer, acceptability for use on roofs with slopes less than 2:12 and directly over corrugated metal deck. For a list of approved underlayment manufacturers supported by Berridge, please refer to the following: HYPERLINK "//www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf" //www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf. Self-Adhering, High-Temperature Underlayment: Provide self-adhering, cold-applied, sheet underlayment, a minimum of 40 mils (1.02mm) thick, consisting of slip-resistant, polyethylene-film top surface laminated to a layer of butyl or SBS-modified asphalt adhesive, with release-paper backing. Provide primer when recommended by underlayment manufacturer. Thermal Stability: Stable after testing at 240 deg�F (116 deg�C); ASTM�D�1970. Low-Temperature Flexibility: Passes after testing at minus 20 deg�F (29 deg�C); ASTM�D�1970. HYPERLINK "http://www.specagent.com/Lookup?ulid=6911" Manufacturers: Subject to compliance with requirements, provide products by one of the following: Grace Ultra Mid-States Asphalt Quick Stick HT Pro Polyglass Polystick MTS Soprema Lastobond Shield HT Tamko TW Underlayment or TW Metal & Tile Underlayment ．如果没有在整个屋顶区域使用自粘的高温衬垫，则保留下面的“毡衬垫”段。如本工程屋面坡度为3:12及以下，则要求铺两(2)层毡。毡层:ASTM�D�226/D�22M, II型(30号)，含沥青有机毡。如果需要16量规子框架，则选择ASTM A653。如果需要22规或24规子框架，则选择ASTM A792。其他金属子框架和水垢:ASTM�C�645;冷弯金属涂层钢板，ASTM�A�653/A�653M, G90 (Z275)热浸镀锌或ASTM�A�792/A�792M, Class AZ50 (Class AZM150)涂层，除非另有说明。为金属面板系统的支撑和对准提供制造商的标准截面。按照要求保留面板配件、闪光板和饰件，并与第076200节“钣金闪光板和饰件”中的规定保持一致。 Panel Accessories: Provide components required for a complete, weathertight panel system including trim, copings, fasciae, mullions, sills, corner units, clips, flashings, sealants, gaskets, fillers, closure strips, and similar items. Match material and finish of metal panels unless otherwise indicated. Closures: Provide closures at eaves and ridges, fabricated of same metal as metal panels. Backing Plates: Provide metal backing plates at panel end splices, fabricated from material recommended by manufacturer. Closure Strips: Closed-cell, expanded, cellular, rubber or crosslinked, polyolefin-foam or closed-cell laminated polyethylene; minimum 1-inch- (25-mm-) thick, flexible closure strips; cut or premolded to match metal panel profile. Provide closure strips where indicated or necessary to ensure weathertight construction. Flashing and Trim: Provide flashing and trim formed from same material as metal panels as required to seal against weather and to provide finished appearance. Locations include, but are not limited to, eaves, rakes, corners, bases, framed openings, ridges, fasciae, and fillers. Finish flashing and trim with same finish system as adjacent metal panels. If required, insert special requirements for ridge closures, corner units, copings, fasciae, and fillers. Gutters: Formed from same material as roof panels, complete with end pieces, outlet tubes, and other special pieces as required. Fabricate in minimum 96-inch- (2400-mm-) long sections, of size and metal thickness according to SMACNA's "Architectural Sheet Metal Manual." Furnish gutter supports spaced a maximum of 36 inches (914 mm) o.c., fabricated from same metal as gutters. Provide wire ball strainers of compatible metal at outlets. Finish gutters to match [metal roof panels] [roof fascia and rake trim]. Downspouts: Formed from same material as roof panels. Fabricate in 10-foot- (3-m-) long sections, complete with formed elbows and offsets, of size and metal thickness according to SMACNA's "Architectural Sheet Metal Manual." Finish downspouts to match gutters. Roof Curbs: Fabricated from same material as roof panels, [0.048-inch (1.2-mm)] 标称厚度;裙子底部突出搭配屋顶板型材，焊接顶盒和整体全长板球。制造遏制0.060英寸 - （1.52mm-）标称厚度，角度，C-或Z形钢板的凝固次焦。制造遏制和亚帧以承受指示的尺寸和高度所示的载荷。完成屋顶路径，以匹配金属屋顶板。用1英寸（25mm-）厚的刚性绝缘材料隔离屋顶遏制。面板紧固件：镀锌钢，耐腐蚀钢，锌铸头或尼龙封端钢，型号和尺寸，如适用的负载要求。暴露的紧固件，在建筑师批准的情况下，应在覆盖物的外侧垫圈或有垫圈的垫圈，以防水渗透。对于批准的密封胶指导，请参阅HyperLink的批准列表//www.efxbank.com/wp-content/uploads/2014/06/apload-materials-form -11-4-13.pdf“http：//www.efxbank.com/wp-content/uploads/2014/06/prapproved-materials-form-11-4-13.pdf。面板密封剂：提供与面板材料兼容的制造商推荐的密封胶类型，是不曝光的，也不会损坏面板完成。 Sealant Tape: Pressure-sensitive, 100 percent solids, gray polyisobutylene compound sealant tape with release-paper backing. Provide permanently elastic, nonsag, nontoxic, nonstaining tape 1/2 inch (13 mm) wide and 1/8 inch (3 mm) thick. Joint Sealant: ASTM�C�920; elastomeric polyurethane or silicone sealant; of type, grade, class, and use classifications required to seal joints in metal panels and remain weathertight; and as recommended in writing by metal panel manufacturer. Butyl-Rubber-Based, Solvent-Release Sealant: ASTM�C�1311. FABRICATION General: Fabricate and finish metal panels and accessories at the factory, by manufacturer's standard procedures and processes, as necessary to fulfill indicated performance requirements demonstrated by laboratory testing. Comply with indicated profiles and with dimensional and structural requirements. On-Site Fabrication: Subject to compliance with requirements of this Section, metal panels may be fabricated on-site using factory set, non-adjustable portable roll-forming equipment if panels are of same profile and warranted by manufacturer to be equal to factory-formed panels. Fabricate according to equipment manufacturer's written instructions and to comply with details shown. Provide panel profile, including major ribs and intermediate stiffening ribs, if any, for full length of panel. Sheet Metal Flashing and Trim: Fabricate flashing and trim to comply with manufacturer's recommendations and recommendations in SMACNA's "Architectural Sheet Metal Manual" that apply to design, dimensions, metal, and other characteristics of item indicated. Form exposed sheet metal accessories that are without excessive oil canning, buckling, and tool marks and that are true to line and levels indicated, with exposed edges folded back to form hems. Sealed Joints: Form nonexpansion, but movable, joints in metal to accommodate sealant and to comply with SMACNA standards. Fabricate cleats and attachment devices from same material as accessory being anchored or from compatible, noncorrosive metal recommended in writing by metal panel manufacturer. Size: As recommended by SMACNA's "Architectural Sheet Metal Manual" or metal panel manufacturer for application, but not less than thickness of metal being secured. FINISHES Protect mechanical and painted finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in same piece are unacceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. Steel Panels and Accessories: Retain one exposed fluoropolymer finish from subparagraphs below. Verify availability of finishes for products specified. If retaining more than one, indicate location of each on Drawings or by inserts. To obtain a proprietary finish system, insert names of coating manufacturers and products. Two-Coat Fluoropolymer: AAMA�621. Fluoropolymer finish containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil over 0.2� 0.05 mil primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Mica Fluoropolymer: AAMA�621. Two-coat fluoropolymer finish with suspended mica flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil over 0.2� 0.05 mil primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.0.24 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Metallic Fluoropolymer: AAMA�621. Two-coat fluoropolymer finish with suspended metallic flakes containing not less than 70 percent PVDF resin by weight in both color coat and clear topcoat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil over 0.2� 0.05 mil primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Finish in "Concealed Finish" Subparagraph below is frequently used as a factory finish for interior surfaces. Concealed Finish: Apply pretreatment and manufacturer's standard white or light-colored acrylic or polyester backer finish consisting of prime coat and wash coat with a minimum total dry film thickness of 0.35 mil (0.009 mm). Aluminum Panels and Accessories: Retain one fluoropolymer finish from subparagraphs below. Verify availability of finishes for products specified. If retaining more than one, indicate location of each on Drawings or by inserts. Revise or insert additional testing requirements in three fluoropolymer subparagraphs below if performance levels indicated in AAMA�2605 are insufficient. Two-Coat Fluoropolymer: AAMA�2605. Fluoropolymer finish containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil over 0.2� 0.05 mil primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Mica Fluoropolymer: AAMA�2605. Two-coat fluoropolymer finish with suspended mica flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil over 0.2� 0.05 mil primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Metallic Fluoropolymer: AAMA�2605. Two-coat fluoropolymer finish with suspended metallic flakes containing not less than 70 percent PVDF resin by weight in both color coat and clear topcoat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil over 0.2� 0.05 mil primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. EXECUTION EXAMINATION Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances, metal panel supports, and other conditions affecting performance of the Work. Retain one or both subparagraphs below. Examine primary and secondary roof framing to verify that rafters, purlins, angles, channels, and other structural panel support members and anchorages have been installed within alignment tolerances required by metal roof panel manufacturer. Examine solid roof sheathing to verify that sheathing joints are supported by framing or blocking and that installation is within flatness tolerances required by metal roof panel manufacturer. Retain subparagraph below with subparagraph above for systems that depend on air- or water-resistive barriers to prevent air infiltration or water penetration. Verify that air- or water-resistive barriers have been installed over sheathing or backing substrate to prevent air infiltration or water penetration. Examine roughing-in for components and systems penetrating metal panels to verify actual locations of penetrations relative to seam locations of metal panels before installation. Proceed with installation only after unsatisfactory conditions have been corrected. PREPARATION Miscellaneous Supports: Install subframing, furring, and other miscellaneous panel support members and anchorages according to ASTM�C�754 and metal panel manufacturer's written recommendations. UNDERLAYMENT INSTALLATION Retain this article for metal roof panels applied over solid roof sheathing. Retain "Self-Adhering Sheet Underlayment" or "Felt Underlayment" Paragraph below or retain both if required. If questions arise on Berridge standard, refer to HYPERLINK "//www.efxbank.com/wp-content/uploads/2013/09/Berridge-Typical-Underlayment-Installation-Details.pdf" //www.efxbank.com/wp-content/uploads/2013/09/Berridge-Typical-Underlayment-Installation-Details.pdf and HYPERLINK "//www.efxbank.com/wp-content/uploads/2013/05/Proper-Felting-Application.pdf" //www.efxbank.com/wp-content/uploads/2013/05/Proper-Felting-Application.pdf for guidance. Self-Adhering Sheet Underlayment: Apply primer if required by manufacturer. Comply with temperature restrictions of underlayment manufacturer for installation. Apply at locations indicated [below] [on Drawings], wrinkle free, in shingle fashion to shed water, and with end laps of not less than 6 inches (152 mm) staggered 24 inches (610 mm) between courses. Overlap side edges not less than 36 inches (914.4 mm).[�Extend underlayment into gutter trough.] Roll laps with roller. Cover underlayment within 14 days. Retain one of two subparagraphs below or delete both if indicated on Drawings. Apply over the entire roof surface. Apply over the roof area indicated below: Revise subparagraphs below to suit Project or delete if indicated on Drawings. If inserting dimensions, note that many self-adhering sheet underlayments are manufactured in 36-inch- (914-mm-) wide rolls. Roof perimeter for a distance up from eaves of [24 inches (610 mm)] [36 inches (914 mm)] beyond interior wall line.Valleys, from lowest point to highest point, for a distance on each side of [18 inches (460 mm)] ．不少于6英寸(152毫米)的薄片两端重叠。宽度为[18英寸(460毫米)]的前角．Hips and ridges for a distance on each side of [12 inches (305 mm)] ．Roof-to-wall intersections for a distance from wall of [18 inches (460 mm)] ．在天窗、烟囱、天窗和其他穿透元件周围，元件距离[18英寸(460毫米)] ．感觉界定：在[下面] [上图]的位置适用，以瓦片时尚到脱落水，并带有不小于36英寸（50毫米）的叠层接头。如果在图纸上指示，请保留下面的两个分段或删除两分项。涂在整个屋顶表面上。涂在未被自粘贴薄板下界覆盖的屋顶上。在自粘附纸下边缘的边缘，不小于6英寸（152.4mm），以瓦片时尚到脱落水。闪光灯：安装闪光灯以覆盖界定以符合第1407200张“钣金闪烁和修剪”中规定的要求。金属面板安装一般：根据制造商的书面指示，尺寸和位置的书面说明安装金属面板。除非另有说明，否则安装垂直于支持的面板。锚固金属板和工作的其他部件牢固到位，具有热和结构运动的规定。 Shim or otherwise plumb substrates receiving metal panels. Flash and seal metal panels at perimeter of all openings. Fasten with self-tapping screws. Do not begin installation until air- or water-resistive barriers and flashings that will be concealed by metal panels are installed. Install screw fasteners in predrilled holes. Locate and space fastenings in uniform vertical and horizontal alignment. Install flashing and trim as metal panel work proceeds. Locate panel splices over, but not attached to, structural supports. Stagger panel splices and end laps to avoid a four-panel lap splice condition. Align bottoms of metal panels and fasten with blind rivets, bolts, or self-tapping screws. Fasten flashings and trim around openings and similar elements with self-tapping screws. Provide weathertight escutcheons for pipe- and conduit-penetrating panels. Fasteners: Steel Panels: Use stainless-steel fasteners for surfaces exposed to the exterior; use galvanized-steel fasteners for surfaces exposed to the interior. Aluminum Panels: Use stainless-steel fasteners for surfaces exposed to the exterior; use stainless-steel fasteners for surfaces exposed to the interior. Anchor Clips: Anchor metal roof panels and other components of the Work securely in place, using manufacturer's approved fasteners according to manufacturers' written instructions. Metal Protection: Where dissimilar metals contact each other or corrosive substrates, protect against galvanic action as recommended in writing by metal panel manufacturer. Standing-Seam Metal Roof Panel Installation: Fasten metal roof panels to supports with concealed clips at each standing-seam joint at location, spacing, and with fasteners recommended in writing by manufacturer. Install clips to supports with self-tapping fasteners. Install pressure plates (if required) at locations indicated in manufacturer's written installation instructions. Retain "Snap Joint" or "Seamed Joint" Subparagraph below; coordinate with products selected in Part�2. If specifying Double-Lock Zee-Lock (180o bend), remove the requirement of the factory-applied Vinyl Weatherseal. Snap Joint: Nest standing seams and fasten together by interlocking and completely engaging factory-applied vinyl weatherseal. Seamed Joint: Crimp standing seams with manufacturer-approved, motorized seamer tool so clip, metal roof panel, and factory-applied vinyl weatherseal are completely engaged. Batten Seam Joint: Nest standing seams and fasten together by installing batten seam cap and completely engage factory-applied vinyl weatherseal. Accessory Installation: Install accessories with positive anchorage to building and weathertight mounting, and provide for thermal expansion. Coordinate installation with flashings and other components. Install components required for a complete metal panel system including trim, copings, corners, seam covers, flashings, sealants, gaskets, fillers, closure strips, and similar items. Provide types indicated by metal roof panel manufacturers; or, if not indicated, types recommended by metal roof panel manufacturer. Flashing and Trim: Comply with performance requirements, manufacturer's written installation instructions, and SMACNA's "Architectural Sheet Metal Manual." Provide concealed fasteners where possible, and set units true to line and level as indicated. Install work with laps, joints, and seams that will be permanently watertight and weather resistant. Install exposed flashing and trim that is without buckling and tool marks, and that is true to line and levels indicated, with exposed edges folded back to form hems. Install sheet metal flashing and trim to fit substrates and achieve waterproof and weather-resistant performance. Expansion Provisions: Provide for thermal expansion of exposed flashing and trim. Space movement joints at a maximum of 10 feet (3�m) with no joints allowed within 24 inches (610 mm) of corner or intersection. Where lapped expansion provisions cannot be used or would not be sufficiently weather resistant and waterproof, form expansion joints of intermeshing hooked flanges, not less than 1 inch (25 mm) deep, filled with mastic sealant (concealed within joints). Gutters: Join sections with riveted and soldered or lapped and sealed joints. Attach gutters to eave with gutter hangers spaced not more than 36 inches (914 mm) o.c. using manufacturer's standard fasteners. Provide end closures and seal watertight with sealant. Provide for thermal expansion. Downspouts: Join sections with telescoping joints. Provide fasteners designed to hold downspouts securely 1 inch (25 mm) away from walls; locate fasteners at top and bottom and at approximately 60 inches (1524 mm) o.c. in between. Retain one of two subparagraphs below. Provide elbows at base of downspouts to direct water away from building. Connect downspouts to underground drainage system indicated. Roof Curbs: Install flashing around bases where they meet metal roof panels. Pipe Flashing: Form flashing around pipe penetration and metal roof panels. Fasten and seal to metal roof panels as recommended by manufacturer. ERECTION TOLERANCES Generally retain this article only for sophisticated or highly finished metal roof panel assemblies. Installation Tolerances: Shim and align substrate or framing within installed tolerance of 1/4 inch in 20 feet (6 mm in 6�m) on slope and location lines as indicated and within 1/8-inch (3-mm) offset of adjoining faces and of alignment of matching profiles. FIELD QUALITY CONTROL Retain "Manufacturer's Field Service" Paragraph below to require a factory-authorized service representative to perform tests and inspections. Manufacturer's Field Service: Engage a factory-authorized service representative to test and inspect metal roof panel installation, including accessories. Report results in writing. Remove and replace applications of metal roof panels where tests and inspections indicate that they do not comply with specified requirements. Additional tests and inspections, at Contractor's expense, are performed to determine compliance of replaced or additional work with specified requirements. Prepare test and inspection reports. CLEANING AND PROTECTION Remove temporary protective coverings and strippable films, if any, as metal panels are installed, unless otherwise indicated in manufacturer's written installation instructions. On completion of metal panel installation, clean finished surfaces as recommended by metal panel manufacturer. Maintain in a clean condition during construction. Replace metal panels that have been damaged or have deteriorated beyond successful repair by finish touchup or similar minor repair procedures. END OF SECTION 074113.16 Copyright 2015 AIA MasterSpec Premium 03/15 PRODUCT MASTERSPEC LICENSED BY ARCOM TO BERRIDGE MANUFACTURING COMPANY. STANDING-SEAM METAL ROOF PANELS074113.16 - PAGE 6 349O]��P \ _ n 5STXY��VWX��VWXY��ü��zqk h�3�0J0hIu9hIu90J0 h�0J0�j�hawGh�W�U h�W�h. h�W�h�W��jhawGh�W�U hawGh�W�jhawGh�W�U h�c�h. h�c�h�c�h�c� h.5� h 2�h 2�h 2�h 2�5�h 2�h 2�h 2�5�>* h.0J. h.0J-h.*4:� � � � ! � � � �� q � l�:�+s�q��)6gd 2�q��h�W�hv ��>�3L4��)gd�68gd�68gdIu9gd�W��gd�W��YZ[`adefghv ��!3�Y��0��ع��ؖ��zv�ofoh�wh8 �0J/ h8 �0J/5�h�� h�wh. h.5�h�wh� �0J/ h8 �0J05�h�wh8 �0J0h�wh.0J/h�wh.0J0h�2h.5� h�2h.hd h.0J/ h.0J0h�h�68h. h�0J/ hS:0J/h�wh�3�0J/ h�3�0J0hIu9hIu90J0(��3E��Y0e�� !�!"�"!#^$�$�$�%�%T&''�'��)gdd �� ^$e$�$�$�$�$�'�'�'�')) ))n)p)q)r)�),,Z,[,],H-W-p-q-~-�-�-�-..E.F.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�� h�as5�h�whs`|5�h�wh�k\5�h�k\hs`|h�wh�E5�h�wh.5�h�EhG_� h�wh. h� �h.h�I@ h�whk[�hQ�h� �h&Y�hk[�h�UDh!i h.5�h.h��7�'�(�()])�)�*+b+�+�+C,�,@-G.�./�/�01B2K2d2�3��)gd�W� &Fgd�w)gd�Y�@& gd�w)��gd�w��.�./�/�/�0�0�01191�1�1A2B2d2�3�3�3�3�3 4 4d4i4j4k4t4u4.5/5s5t5u5�5�5�5�5�5�566U7X7[7`7W9[9��ƻ��Ɵ��Ɣƻ��~�~Ɣ�y�y�y h.5�h�W�h�W�5��j�hEqh�W�U h�W�h.h32� h�wh�W��j�hEqh�W�U hEqh�W�jhEqh�W�U h�W�h�W�h�i�h�Y�h�wh�Y�mH sH h!imH sH h�Y�mH sH h!ihG_�h.h�k\/�3u4.56�6w7�8"9�9:�:�::;�;p<�<B=w=s>�> ?o@A�A�AC��)gdo��gd�w))gd�W�gd�W�[9^9j9�9�9�9�9�9�9�9�9�:�:�: ;;;;;+;:;u;�;�;�;�;�;�;<<5<9<:<D<�<�<�<�<== ==\=]=i=k=q=��ľ��vho0J/mH sH ho0J0mH sH hP�h�wh.mH sH h�wh.0J/mH sH h�wh.0J0mH sH h�wh.hB � h.0J/ ho0J/ h.0J0 ho0J0h[jShomH sH homH sH hoh_F hoh. h.5�h..q=r=u=w=??+A4A?AJASA_ArAuA�A~C�C�C�C�C DDD D*D�D�D�D�D�DEE8E9E:ERESE]E}E�E�E��½�½׽׹��{tm h�wh�lF hS:h�lF h�h�lF�j�hawGh�lFU hawGh�lFjhawGh�lFUh�=� h� �5� hm�5� h�lF5�h�h�lF h.5� h.0J/5� h.0J05� h�wh.h.h�wh.mH sH h�wh.0J/mH sH h�whP�0J/mH sH (C~CE8FVFHG�GHpH1I�IJJ�JjK�K�KL�LM�NO�O(PgP��)gd�lF��gd�lF)gd�w��gd�lFgd�lF��gd�lFgd�lF)�E�E�E�E�E�E�E�E�E�EFF FF8F9FSFUFVFsFtF�F�F�FHG_GoG�G�G�G�G�G�G�G�G�GHHH��»��~w~pip�~b h��0J05� h �0J/5� h�lF0J/5� h �0J05� h�lF0J05�hL~ h�F�mH sH hL~ hL~ h�lF0J/ h�lF0J0h'4� hawGh�lFhBI>h�lF5�h�lF h�h�lF hEqh�lFh�wh�5� h�wh� h�wh�7v�j�h�wh�lFU h�wh�lFjh�wh�lFU&H HHHHHH)H?HBHTHWHmHnHpH0I1IRISI_I~I�I�I�I�I�I�I�I�I�I�I�I�IJ8J:JHJmJwJ�J�J�J�J�J�JiKjKuK��ǿ�ǻ��Ǫ��摋��|�h�G h�Gh�Gh.Q h�lF0J/ h�lF0J0h�h�lF5�h�wh[?gmH sH h[?gmH sH h�F=h[?g0J:h[?gjh[?gU h[?gh[?gh� �hm�hwC� h�lF5� hS:hS:h�lF h��0J/5� h�lF0J/5� h�lF0J05�/uKK�K�K�K�K�K�K�K�K�KLL$L%L1LPLRLSLrLsLtLL�L�L�L�L�L�L�L M MMM�M�M�M�M�M�MLNMNQN�N�N�N�N�N�N�N�N�N�N�O��˺Ӻ��˟ӛ��撊��h�wh�I�5�h� h�I�5�h��h��mH sH h�h�lF5�h�wh[?gmH sH h[?gmH sH h�F=h[?g0J:jh[?gU h[?gh[?g h�lF5� h�wh�lFh�lFh[?gh�wh�lF0J/h�wh�lF0J05�O�O�O�O�O�O�O�O�O�O�O�O�O�O�O�O2P=PHPxPzP}P�P�P�P�P�P�P�P�P�P�P�P�P�P�P�P�P�P�P�P�PtSxS�S�S TTTmToTpT��Ļ��߳��h�S1hIu9mH sH hIu9mH sH jhIu9UmH sH h�S1mH sH h�S1h.hwC�h�wh�lF0J/h�wh�lF0J0hS: h!|�0J/5� h!|�0J05�h�lF h �0J/5� h�lF0J/5� h �0J05� h�lF0J05�3gP�P�P�PAR�S�T,V{V�VuW�W�W�W�WX/XY_YwY�Yg[��gdS:)gd�w@& gd�wgdL~ gd�@ZgdawG��gd�w@& gd�w��)gd�lF��gd�wpT�T�T�T�T>UAUEUGUKUNUWV`VlV�V�V�V�V�VWWW W!W0WuW�W�W�W�WXXX,X.X/X�X��ľ��ľ�ľЭ��}y}rnfn_� hawGhawGhBI>hawG5�hawG hawGh�@Zh9xh�@Zh�h��0J;>*B*ph� h�h��j�hawGh�U hawGh�jhawGh�U h�lF0J/ h.0J/ h.0J0 h�lF0J0h.h�wh�lFmH sH hIu9mH sH jhIu9UmH sH h�F=hIu90J:mH sH $�XYYwY�Y�YoZrZxZyZzZ�Z�Z�Z�Z�Z�^�^�^�a�a�aBbKbTb�b�b�bcJcRcYcGdQdZd\dndee*ef ff;f=fsgug�g�g�gh��鵮��靔鍅��h��jh��U h��h��h�wh�J�aJhS:h.aJh�h.5� h.0J/5� h.0J05� h.5�hS: hS:hS: hS:0J/ h.0J/ h.0J0hU,� hU,�hU,�h.h�wh.mH sH h�S1mH sH 2g[�[(]�]�];_�`ac d�e,fugph i�i�j(k4kdl�mTnVop�pFq�q��gd�w)gd�w��)hhhmhnhohph�i�i�i�i�i�i�l�l�l�l�u�u�uvv,v�v�v�v�w�x�x�x@yCy�y�z�z�zu|w|x|}|�|�|�|�}�}�}�~Z[c��X�Y�`� � ��u�v�|��ں�Դ�ନ�ĨࡨĨ��ࡨĨ� h�Wh�Wh�Wh�WmH sH h+H0J/ h+H0J0h��hR�h�Ch9xh+H h.0J/ h.0J0h. h��h��hH�h��0J:jh��Uh��>�q�q�r�stCu wy:{�{�|�|o} ~�� Ćd��)�Љ�7��Ҏ�� s� �f��N��w��]��x��'��)��׊؊�M�O�P��̋�� q�r�s��?�D�G�R��č͍֍ ��G��%�.�1�:�C�E�W��ɐҐԐ� ��h�h.5� h.0J/5� h.0J05� h��0J/ h��0J0 h.0J/ h.0J0 h.5�h.h�wh.mH sH hIu9mH sH h%h��0J:mH sH h��h��mH sH jh��UmH sH h��mH sH 6�>�G�P�R�d�� ے��;�>�D�L�A�B�I�K�P�S��Ěz��:�;�b�c��)��ٟY��hU,�h�Yh�wh.mH sH h�~mH sH h�wh�X�H*mH sH h�X�mH sH h�YmH sH h�� h��0J/ h.0J/ h.0J0 h��0J0 h.5�h�h.5� h.0J/5� h.0J05�h.6'��o��ř\��W�+�b�ԝ��+�ٟl�7�s�ӣ��ɨ�9�v�éT�h��)��Y�Z�^�j�l�d�k�q��r�x��K�T�]�L�R�Z�� (�;�I�~��İŰ˰��6�7��¼¶��̒� h�r10J. h!Qc0J, h� �0J,h6uh��0J,hEqh��0J, h�r10J, h�r10J+h�r1 h�r10J*h?�hn6{h-y�jh-y�Uh�Y h.0J/ h.0J0h.h'Mh��h�G9h�ͪϫ�t�*��V�{��x��˰��$a$gdEq$a$gd!Qc2')��7�N�O�P�Q�R�S�T�U�V��'2Ekd�$$If�A�0��$�P��4� Aa�1$If$If4 7�@�C�D�J�K�L�M�P�Q�R�S�T�U�V��h.h-y�h?�hn6{h�N mHnHujh�r1Uh�r1 h�r10J-/<0BP��/ ��=!��"��#��$��%�� D��y��K��y��K��http://www.arcomnet.com/sustainable_design.aspx?topic=6yX��;H�,�]ą'c��D��y��K��y��K��http://www.arcomnet.com/sustainable_design.aspx?topic=7yX��;H�,�]ą'c��D��y��K��y��K��http://www.arcomnet.com/sustainable_design.aspx?topic=30yX��;H�,�]ą'c��D��y��K��y��K��http://www.arcomnet.com/sustainable_design.aspx?topic=27yX��;H�,�]ą'c��D��y��K��y��K�lhttp://www.specagent.com/Lookup?ulid=6906yX��;H�,�]ą'c��D��y��K��y��K�zhttp://www.specagent.com/Lookup?uid=123457046510yX��;H�,�]ą'c��D��y��K��y��K�lhttp://www.specagent.com/Lookup?ulid=6911yX��;H�,�]ą'c��V$$If�!vh#v�#vP:V�A��5��5�P4�4� A"@|��666666666vvvvvvvvv666666>666666666666666666666666666�6666666666�666666666666hH66666666666666666666666666666666666666666666666666666666666666666�62�� 0@P`p��2(�� 0@P`p�� 0@P`p�� 0@P`p�� 0@P`p�� 0@P`p�� 0@P`p��8X�V~��8X�V~�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@_HmH nH sH tH <`��< NormalCJ_HmH sH tH DA`��D Default Paragraph FontVi@��V 0 Table Normal :V�4�4� la�(k ��( 0No List 6�O�6 HDR$ ��$*$a$4�O4 FTR$ ��$*$a$0�O"0 SCT$��*$a$<�OR< PRT$$ &F��*$@&a$:�b: SUT$ &F��*$@&a$:�b: DST$ &F��*$@&a$<�Ob< ART$$ &F��*$@&a$:�Ob: PR1$ &F��*$@&a$6�Or6 PR2$ &F*$@&a$6�O�6 PR3$ &F*$@&a$6��6 PR4$ &F*$@&a$6��6 PR5$ &F*$@&a$8�b8 TB1$� ��*$^� a$8�r8 TB2$�`��*$^�`a$8��8 TB3$��*$^��a$8��8 TB4$��*$^��a$8��8 TB5$� ��*$^� a$8��8 TF1 $� ��*$^� a$8��8 TF2!$�`��*$^�`a$8��8 TF3"$��*$^��a$8��8 TF4#$��*$^��a$8��8 TF5$$� ��*$^� a$&�R& TCH%*$6�b6 TCE&��p�*$^��`�p�0�Or0 EOS'$��*$a$@��@ ANT($��*$a$<�>*B* ph��H�O�H 7EqCMT)$��*$a$<�B*mHph�sHtH�O�� CPR�O�� SPN�O�� SPD�O�� NUM�O�� NAM �o�� SIB* �o�� IPB*,�O, RJUST1$a$4@"4 3�DX0Header 2 �H�$.��1. 2�DX0Header Char4 @B4 5�DX0Footer 4 �H�$.��Q. 4�DX0Footer Char��Ob� 8 2�TIPJ6��$d%d&d'dN��O��P��Q��B* CJmHph�8sHtHD�/��qD )EqCMT Char<B*CJmHph�sHtH4�/��4 6 2�TIP Char <�B* ph�8>�/��> �0. SustHyperlink >*B*ph�6U`��6 �0.0 Hyperlink >*B*ph�:�o��: S:SAhyperlink >*B*ph�l �� +oHPM_CMTd<$��$d!%d$&d!'d$*$-D�M� ��N��!O��$P��!Q��$a$ B*aJph�x��x s`|PRNW=$d!%d$&d!'d$-DM� ��N��!O��$P��!Q��$P��P ?�0 Balloon Text>CJOJQJaJmHsHtHN�/��N >�0Balloon Text CharCJOJQJ^JaJPK!��pO�[Content_Types].xml��j�0E��ж�r�(��΢�]��yl��#!MB��;.��n�̽�̨\�A�1&�ҫ�� QW��Kv�Ub�OX�#&��1`R��T�9<�l�#��$��>��r�� `�С�-�;c=1g ��?}��~�O��:~��k�ҏM�݄��׷�� )I0w�K�)K`q��f�ݢ�F�H�b�?��G+D�7�H��Ȍ x�|i��R�ǇqbO��Y��PΥ�y�L#��R�=E��6w�R#ϣ��\16h>�((�)��1��!F\OI�1��yA�"֐LəQM�c�@^V6��o#6�ϝ��U�Q�)�F��R��r��Fr��B7�2aʜ� sn�y��z��?�� rn�y�ӑCv�(Yذ��:�~%��'L��̼C�9��c_��l��j5x�S��,�<�̨�Ɋ�VR�ohzB�+~K��O�OI�̲��u�k##7��~F��mKw��{�� 7�n��_��n�?/��绗�B�x˭k�YW[�d��}N(��'\m�9��zj��"�Cy'�.ʐ�q2&�""��h;��+�D�pqg�8l�հշ��er�f�k�.Ns��Hl�k~9"G�ڛ��ҽb��5i{�d&��D{=(��!hjew¢kaё�ש�a�ʬ��Ɂ�V��=0#x�B�d��T��y��L�`��M��v�L$�r3I�Ȩ�c4�Eu��иi��d(�|PZ��X�6�`�� 4Օ��e�m5}(�-z��0Y@�p��E4��g��6ʲȸ"�W��AB�J��+�_��JC�z�%�Y��A��$��BO�6"#��Za��o��l �ĳK�.��J�o�eg��z��m�o�1��QT5��#��Q�Qt1��J�K:ꬌ�vV��h�g�l�zP�nZv��ޮ{��&��i��v3fX��Xޮ�k��!M�;|.�ے�]k��>��2~��{��Q�LfP��weXjv1j��v�&��~k�v+ne��N��`�]�04_�+U�՗��;{ �1��K*�J%|z�l�&jO��"�Dqk��H�}]��^��J��*^ӫU:~�Y��~�>��uË(�*��/��]۽�%U��Tq��! :�[�q��*�f\�N��a+h��t�o\�B��~3�Z�N�U��תI��n��5}����b+�壈�W�:��PK! ѐ��'theme/theme/_rels/themeManager.xml.rels��M �0��wooӺ�&݈Э��5 6?$Q�� ,.�a��i��c2�1h�:�q��m��@RN��;d�`��o7�g�K(M&$R(.1�r'J��ЊT��8��V�"��AȻ�H�u}��|�$�b{��P��8�g/]�QAsم(��#��L�[��PK-!��pO�[Content_Types].xmlPK-!�֧��6-_rels/.relsPK-!ky��theme/theme/themeManager.xmlPK-!o(ʾ��theme/theme/theme1.xmlPK-! ѐ��'� theme/theme/_rels/themeManager.xml.relsPK]� V� �� Y��.[9q=�EHuK�OpT�Xh��Y�7�V�Y\^`bcefghjkmpqsvq��'�3CgPg[�q�'�h��V�Z[]_adilnortu� � � W � � �+�+ ,.-t-�-=9=R=�=�=�=RA�A�A$DRDrD�E�ELF LoL�L�NO O�_`m`ׂO��q�V�X��X��X��X��X��X��X��X��X��X��X��X��X��X��!��@� @��H ��0�( � ��0�( �0�v�( ��B �S�� ?��userSustainabilityTopic_6_1userSustainabilityTopic_7_1userSustainabilityTopic_30_1userSustainabilityTopic_27_1ptBookmark6911� W e*v,�NW�U s,.PW��4�4^5a5f5h58>8>�> ?�O�O�O�O�O�O�O�O�O�O�V�VUZXZ�`�`GaVa�a�a�a�a-h9h^�a��C�M�T�W�49:��y)�)8>U>��T�W�333��N��eDW��^�`�OJQJo(�8��^�8`��OJQJo(��^�`��OJQJ^Jo(o�� p^�� `��OJQJo(�� @^�� `��OJQJo(��x��^�x`��OJQJo(��H��^�H`��OJQJ^Jo(o��^�`��OJQJo(��^��`��OJQJo(�� PART - SCHEDULE - PRODUCT DATA SHEET - �`��`^�``��.�`��`^�``��.��^��`��.��^��`��.� �� ^� `��)�` ��` ^�` `��) ��)@!Qo@po9@!��PW�W�'MSx�! �RL~ y �N d ��H�CD_�[o�~�.�E�2�l�U#�e$2'�$(H(�0*�c+�=-} .'+.�0.6X.i/� 0�61�S1�r1~:7�8�68Iu9S:S:_x>�I@pM@�f@�BB�GB�C�8C�UD_F�lF�GawG+H+oH�I`uKNv_P.QZ@RgST�U�DX�Y�@Z�k\A#a1 � ^��X�&Y�� ?��W��x��e� ��]� ^�8 ��F�!8� ��v��^�J(�wC�P�� V��J��:�'��;m��i��Y��i��G�Gs��ko�R�z[��r��N��I�Q� 2��F�G_�!|��!8��M�Qa��]��1�B ��x��J�2��7�32��X�� m�� 3��=�.�^S��c�U,�k[��V��}�� DOIFormatMF04MF95MFOrigin SectionIDSpecTypeuserSustainabilityVar_27_1userSustainabilityVar_30_1userSustainabilityVar_6_1userSustainabilityVar_7_1Version03/01/1510741131607412MF041602 MasterSpec*27^userSustainabilityTopic_27_1^1,^<SustainabilityTopic id="27"><TopicText id="228"><RatingSystems><System id="1"/></RatingSystems> <Content><CMT>"Solar Reflectance Index" Paragraph below applies to LEED 2009. First option is minimum for roofs with slopes of 2:12 or less; second option is for roofs with slopes steeper than 2:12.</CMT><PR1>Solar Reflectance Index: Not less than [78] [29] when calculated according to ASTM�E�1980, based on testing identical products by a qualified testing agency.</PR1></Content> </TopicText></SustainabilityTopic>�30^userSustainabilityTopic_30_1^1,^<SustainabilityTopic id="30"><TopicText id="239"><RatingSystems><System id="1"/></RatingSystems> <Content><CMT>Retain "Recycled Content" Paragraph below to specify recycled content if required. An alternative method of requiring recycled content is to retain requirement in Project's Division�01 sustainable design requirements Section that gives Contractor the option and responsibility to determine how recycled content requirements will be met.</CMT><PR1>Recycled Content: Postconsumer recycled content plus one-half of preconsumer recycled content not less than <Insert value> percent.</PR1></Content> </TopicText></SustainabilityTopic>O6^userSustainabilityTopic_6_1^1,^<SustainabilityTopic id="6"><TopicText id="167"><RatingSystems><System id="1"/></RatingSystems> <Content><PR2>Product Test Reports: For roof materials, documentation indicating that roof materials comply with Solar Reflectance Index requirements.</PR2></Content> </TopicText></SustainabilityTopic>-7^userSustainabilityTopic_7_1^1,^<SustainabilityTopic id="7"><TopicText id="168"><RatingSystems><System id="1"/></RatingSystems> <Content><PR2>Product Data: For recycled content, indicating postconsumer and preconsumer recycled content and cost.</PR2></Content> </TopicText></SustainabilityTopic>11745�@�8>8>��8>8>V�@��Unknown��G��*�Ax� �Times New Roman5��Symbol3��*�Cx� �Arial5��.�[`�)�Tahoma?� �*�Cx� �Courier New;��WingdingsA��$B�Cambria Math"��h�h�F��F��Bg(i�V1(i�V1!��2;�;�K�Q��HP �� $P��DX !xx��:f��3SECTION 074113.16 - STANDING-SEAM METAL ROOF PANELSSTANDING-SEAM METAL ROOF PANELSBAS-12345-MS80ARCOM, Inc.Microsoft Office User �� Oh��+'��0��(< \h �� '4SECTION 074113.16 - STANDING-SEAM METAL ROOF PANELS STANDING-SEAM METAL ROOF PANELS ARCOM, Inc.BAS-12345-MS80 Normal.dotmMicrosoft Office User2Microsoft Macintosh Word@@2BMGo�@�>`��@�>`��(i�� ՜.��+,��D��՜.��+,��x4 px�� ' MicrosoftH1V;�4SECTION 074113.16 - STANDING-SEAM METAL ROOF PANELS Title 8@ _PID_HLINKS'A� T|'Rhttp://www.berridge.com/wp-content/uploads/2013/05/Proper-Felting-Application.pdf=J$jhttp://www.berridge.com/wp-content/uploads/2013/09/Berridge-Typical-Underlayment-Installation-Details.pdf)*!Whttp://www.berridge.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdfy*http://www.specagent.com/Lookup?ulid=6911)*Whttp://www.berridge.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdfv}_http://www.berridge.com/wp-content/uploads/2013/03/Berridge-Tee-Panel-Installation-Details.pdf( http://www.berridge.com/colors/( http://www.berridge.com/colors/A^1http://www.specagent.com/Lookup?uid=123457046510~ *http://www.specagent.com/Lookup?ulid=6906Q5 9http://www.arcomnet.com/sustainable_design.aspx?topic=27P29http://www.arcomnet.com/sustainable_design.aspx?topic=30T8http://www.arcomnet.com/sustainable_design.aspx?topic=7U8http://www.arcomnet.com/sustainable_design.aspx?topic=6 !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvw��yz{|}~��Root Entry�� FP�z��@Data ��x1Table��EWordDocument ��1�SummaryInformation(��DocumentSummaryInformation8��MsoDataStore��z��z��3XX��T�SJ�EV�QGHVLQ==2��z��z��Item �� Properties��UCompObj��r��