��ࡱ�>��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� ���bjbj~~ 1�{{c���������((� � � � � ����� � � 8� T-!\� �9��!p�!"""�"��#$�#�8�8�8�8�8�8�8,*;��=%9� �#�"�"�#�#%9�(� � ""�:9�(�(�(�#Z� "� "�/, �(�#�8�(�(:k-,�-���� :*��������0%��- �/P90�9�- �>�(�>�-�(� �- �#�#�#%9%9�(�#�#�#�9�#�#�#�#���������������������������������������������������������������������>�#�#�#�#�#�#�#�#�#(+ S:   SECTION 074213.13 - FORMED METAL WALL PANELS TIPS: To view non-printing Editor's Notes that provide guidance for editing, click on Masterworks/Single-File Formatting/Toggle/Editor's Notes. Revise this Section by deleting and inserting text to meet Project-specific requirements. This Section uses the term "Architect." Change this term to match that used to identify the design professional as defined in the General and Supplementary Conditions. GENERAL RELATED DOCUMENTS Retain or delete this article in all Sections of Project Manual. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division�01 Specification Sections, apply to this Section. SUMMARY Section Includes: Exposed-fastener, lap-seam metal wall panels. Related Sections: Retain subparagraphs below to cross-reference requirements Contractor might expect to find in this Section but are specified in other Sections. Section�074213.16 "Metal Plate Wall Panels" for solid metal plate wall panels. Section�074213.19 "Insulated Metal Wall Panels" for foamed-in-place, laminated and honeycomb insulated metal wall panels. Section�074213.23 "Metal Composite Material Wall Panels" for metal-faced composite wall panels. Section�074293 "Soffit Panels" for metal panels used in horizontal soffit applications. PREINSTALLATION MEETINGS Retain "Preinstallation Conference" Paragraph below if Work of this Section is extensive or complex enough to justify a conference. Preinstallation Conference: Conduct conference at [Project site] .如果需要,插入13100节“项目管理和协调”中没有提到的与会者名单。如有需要,保留以下分段;修改为包含更具体的会议信息。与业主、建筑师、业主保险公司(如适用)、金属面板安装商、金属面板制造商代表、结构支撑安装商以及与金属面板有接口或影响的安装商(包括门、窗和百叶窗安装商)会面。审查并确定施工进度,确认材料、安装人员、设备和设施的可用性,以确保施工进度和避免延误。审查与金属面板安装相关的方法和程序,包括制造商的书面说明。检查支撑条件是否符合要求,包括结构构件之间的对齐和连接。检查闪光,特殊壁板细节,墙壁穿透,开口,以及其他影响金属板的建筑状况。审查有关保险、证书、测试和检查的法规和要求(如适用)。 Review temporary protection requirements for metal panel assembly during and after installation. Review of procedures for repair of metal panels damaged after installation. Document proceedings, including corrective measures and actions required, and furnish copy of record to each participant. ACTION SUBMITTALS Product Data: For each type of product. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for each type of panel and accessory. Sustainable Design Submittals: Product Data: For recycled content, indicating postconsumer and preconsumer recycled content and cost. Shop Drawings: Include fabrication and installation layouts of metal panels; details of edge conditions, joints, panel profiles, corners, anchorages, attachment system, trim, flashings, closures, and accessories; and special details. Accessories: Include details of the flashing, trim, and anchorage systems, at a scale of not less than 3" = 1'-0" (1:5). Calculations: Include calculations with registered engineer seal, verifying wall panel and attachment method resist wind pressures imposed on it pursuant to applicable building codes. Retain "Samples for Initial Selection" and "Samples for Verification" paragraphs below for two-stage Samples. Samples for Initial Selection: For each type of metal panel indicated with factory-applied finishes. Include Samples of trim and accessories involving color selection. Samples for Verification: For each type of exposed finish, prepared on Samples of size indicated below: Metal Panels: 12 inches (305 mm) long by actual panel width. Include fasteners, closures, and other metal panel accessories. INFORMATIONAL SUBMITTALS Coordinate "Qualification Data" Paragraph below with qualification requirements in Section�014000 "Quality Requirements" and as may be supplemented in "Quality Assurance" Article. Qualification Data: For Installer and Manufacturer. Product Test Reports: For each product, for tests performed by a qualified testing agency. Retain "Field quality-control reports" Paragraph below if Contractor is responsible for field quality-control testing and inspecting. Field quality-control reports. Sample Warranties: For special warranties. CLOSEOUT SUBMITTALS Maintenance Data: For metal panels to include in maintenance manuals. QUALITY ASSURANCE Installer Qualifications: An entity that employs installers and supervisors who are trained and approved by manufacturer. Manufacturer Qualifications: Company specializing in Architectural Sheet Metal Products. Mockups: Build mockups to verify selections made under Sample submittals and to demonstrate aesthetic effects and set quality standards for fabrication and installation. Retain first subparagraph below for large-scale mockup. Indicate portion of building represented by mockup on Drawings or draw mockup as separate element. Revise to suit Project or if larger mockup is needed for field performance testing. Build mockup of typical metal panel assembly [as shown on Drawings] ,包括[角,][拱腹,]支撑,附件和附件。水喷试验:对金属面板组件模型进行水喷试验,根据AAMA—501.2测试透水性。如果模型不仅仅是为了建立外观因素,那么保留下面的第一小节。对模型的批准不构成对模型中包含的合同文件偏差的批准,除非建筑师特别书面批准该偏差。如果你想对014000节“质量要求”中关于拆除和移除模型的默认要求做一个例外,请保留下面的分段。根据要求,批准的模型可能成为完成工作的一部分,如果在实质性完成时没有受到干扰。交付、储存和处理交付部件、金属面板和其他制成品,以避免损坏或变形。包装金属板在运输和搬运过程中保护。卸载、储存和竖立金属板的方式应防止弯曲、翘曲、扭曲和表面损坏。在平台或托盘上水平堆放金属板,并盖上合适的防风雨通风罩。 Store metal panels to ensure dryness, with positive slope for drainage of water. Do not store metal panels in contact with other materials that might cause staining, denting, or other surface damage. Remove strippable protective covering on metal panels as panels are being installed. Do not leave the film on installed panels. FIELD CONDITIONS Weather Limitations: Proceed with installation only when existing and forecasted weather conditions permit assembly of metal panels to be performed according to manufacturers' written instructions and warranty requirements. COORDINATION Coordinate metal panel installation with rain drainage work, flashing, trim, construction of soffits, and other adjoining work to provide a leakproof, secure, and noncorrosive installation. WARRANTY When warranties are required, verify with Owner's counsel that special warranties stated in this article are not less than remedies available to Owner under prevailing local laws. Galvalume Substrate Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of metal panel systems that fail in materials or workmanship within specified warranty period. Failures include, but are not limited to, the following: Structural failures including rupturing or perforating. Deterioration of metals and other materials beyond normal weathering. Warranty Period: 20 years and 6 months from date of Substantial Completion. Special Warranty on Panel Finishes: Manufacturer's standard form in which manufacturer agrees to repair finish or replace metal panels that show evidence of deterioration of factory-applied finishes within specified warranty period. Usually retain "Exposed Panel Finish" Subparagraph below for fluoropolymer finishes; verify availability with manufacturer. Exposed Panel Finish: Deterioration includes, but is not limited to, the following: Color fading more than 5�Hunter units when tested according to ASTM�D�2244. Chalking in excess of a No.�8 rating when tested according to ASTM�D�4214. Cracking, chipping, peeling, or failure of paint to adhere to bare metal. Finish Warranty Period: 20 years from date of Substantial Completion. PRODUCTS PERFORMANCE REQUIREMENTS Retain "Recycled Content" Paragraph below to specify recycled content if required. An alternative method of requiring recycled content is to retain requirement in Project's Division�01 sustainable design requirements Section that gives Contractor the option and responsibility to determine how recycled content requirements will be met. Recycled Content: Postconsumer recycled content plus one-half of preconsumer recycled content not less than 29 percent. In completing this section, refer to the chart at  HYPERLINK "//www.efxbank.com/technical/testing-summary-chart/" //www.efxbank.com/technical/testing-summary-chart/ for technical guidance based on the panel profile being utilized. Structural Performance: Provide metal panel systems capable of withstanding the effects of the following loads, based on testing according to ASTM�E�1592: Wind Loads: As indicated on Drawings. Deflection Limits: For wind loads, no greater than [1/180] [1/240] 跨度。对于ASTM E 1680,E283,E1646和E331测试报告,请访问//www.efxbank.com/technical/astm-air-water-infiltration-reports/。空气渗透:空气泄漏不超过0.01 CFM / SQ。FT。根据ASTM�e�283在以下测试压力差的情况下测试时(0.05˚L/ s,每平方米):测试压力差:6.24 LBF / SQ。FT。(300Pa)水渗透在静压下:根据ASTM�e�331在以下测试压力差的情况下测试时没有水渗透:测试压力差:6.24 LBF / SQ。ft。(300 pa)。露出的紧固件,搭接金属壁板一般:提供由侧面的侧边缘和机械连接面板组装的工厂形成的金属面板,以使用侧圈中的暴露的紧固件来支撑。包括Weathertight安装所需的配件。为所需的每种产品插入绘图指定。在图纸上使用这些名称以识别每个产品。 Tapered-Rib-Profile, Exposed-Fastener Metal Wall Panels :由凸起的梯形大肋和大肋之间的平底锅构成。设计基础产品:在符合要求的前提下,提供贝里奇制造公司;Deep Deck或类似的产品由以下之一: .金属涂层钢板:符合ASTM�A�792/A�792M, Class AZ50 (Class AZM150)涂层指定的铝锌合金涂层钢板;结构质量。采用卷涂工艺进行预涂,符合ASTM�A�755/A�755M要求。公称厚度:[0.024英寸(0.61毫米)][0.029英寸(0.74毫米)]。外观漆面:[双涂层氟聚合物][云母氟聚合物][金属氟聚合物]参见颜色表: HYPERLINK“//www.efxbank.com/colors/”//www.efxbank.com/colors/。颜色:[根据制造商的指定][匹配建筑师的样品][由建筑师从制造商的全系列中选择] .Aluminum Sheet: Coil-coated sheet, ASTM�B�209 (ASTM�B�209M), 3105 alloy as standard with manufacturer, with H14 temper as required to suit forming operations and structural performance required.Thickness: [0.032 inch (0.81 mm)] [0.040 inch (1.02 mm)].Surface: Smooth, flat finish.外观漆面:[双涂层氟聚合物][云母氟聚合物][金属氟聚合物]参见颜色表: HYPERLINK“//www.efxbank.com/colors/”//www.efxbank.com/colors/。颜色:[根据制造商的指定][匹配建筑师的样品][由建筑师从制造商的全系列中选择] .重型肋骨间距:7.2英寸(182mm)O.C。面板覆盖:36英寸(914毫米)。面板高度:1.5英寸(38毫米)。垫层材料保留了本文施加在护套上的金属壁板的适当段落。自粘附,高温下划线只能在易受泄漏的壁开口闪烁条件下应用,毛毡施加在墙壁的其余部分上;或界定可以应用于整个墙区域。下面的“自粘附,高温下界”段落中列出的垫片适用于与金属壁应用相关的更高温度。修改是否不需要高温下界。使用底层制造商进行验证,可接受在墙壁应用上使用,直接在波纹金属甲板上。 For a list of approved underlayment manufacturers supported by Berridge, please refer to the following:  HYPERLINK "//www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf" //www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf. Self-Adhering, High-Temperature Underlayment: Provide self-adhering, cold-applied, sheet underlayment, a minimum of 40 mils (1.02 mm) thick, consisting of slip-resistant, polyethylene-film top surface laminated to a layer of butyl or SBS-modified asphalt adhesive, with release-paper backing. Provide primer when recommended by underlayment manufacturer.  HYPERLINK "http://www.specagent.com/Lookup?ulid=6911" Manufacturers: Subject to compliance with requirements, provide products by one of the following: Grace Ultra Mid-States Asphalt Quick Stick HT Pro Polyglass Polystick MTS Soprema Lastobond Shield HT Tamko TW Underlayment or TW Metal & Tile Underlayment .热稳定性:在240degīf(116deg�c)测试后稳定;Astm�d�1970。低温柔韧性:在减去20degīf的测试后通过(29deg�c);Astm�d�1970。如果没有使用自粘附,高温衬垫,保留下面的“感觉障碍”段落。毛毡界限:ASTM�D�226/d�22M,型�II(No.Ing�30),沥青饱和有机毡。杂项材料如果需要16个测量次距,则选择ASTM A653。如果需要22个Gage或24个计量次帧,则选择ASTM A792。杂项金属次焦和毛刺:ASTM�C�645,冷成型金属涂层钢板,ASTM�A�653/A�653M,G90(Z275)热浸镀锌涂层指定或ASTM��792/ a除非另有说明,�792M,Class�AZ50(类AZM150)铝 - 锌合金涂层指定。 Provide manufacturer's standard sections as required for support and alignment of metal panel system. Retain panel accessories, flashing, and trim as required and coordinate with those specified in Section�076200 "Sheet Metal Flashing and Trim." Panel Accessories: Provide components required for a complete, weathertight panel system including trim, copings, fasciae, mullions, sills, corner units, clips, flashings, sealants, gaskets, fillers, closure strips, and similar items. Match material and finish of metal panels unless otherwise indicated. Closures: Provide closures at eaves and rakes, fabricated of same metal as metal panels. Backing Plates: Provide metal backing plates at panel end splices, fabricated from material recommended by manufacturer. Closure Strips: Closed-cell, expanded, cellular, rubber or crosslinked, polyolefin-foam or closed-cell laminated polyethylene; minimum 1-inch- (25-mm-) thick, flexible closure strips; cut or premolded to match metal panel profile. Provide closure strips where indicated or necessary to ensure weathertight construction. Flashing and Trim: Provide flashing and trim formed from same material as metal panels as required to seal against weather and to provide finished appearance. Locations include, but are not limited to, bases, drips, sills, jambs, corners, endwalls, framed openings, rakes, fasciae, parapet caps, soffits, reveals, and fillers. Finish flashing and trim with same finish system as adjacent metal panels. Panel Fasteners: Self-tapping screws designed to withstand design loads. Provide exposed fasteners with heads matching color of metal panels by means of factory-applied coating. Provide EPDM or PVC sealing washers for exposed fasteners. For approved sealant guidance refer to the approved list at  HYPERLINK "//www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf" //www.efxbank.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf. Panel Sealants: Provide sealant type recommended by manufacturer that are compatible with panel materials, are nonstaining, and do not damage panel finish. Sealant Tape: Pressure-sensitive, 100 percent solids, gray polyisobutylene compound sealant tape with release-paper backing. Provide permanently elastic, nonsag, nontoxic, nonstaining tape 1/2 inch (13 mm) wide and 1/8 inch (3 mm) thick. Joint Sealant: ASTM�C�920; elastomeric polyurethane or silicone sealant; of type, grade, class, and use classifications required to seal joints in metal panels and remain weathertight; and as recommended in writing by metal panel manufacturer. Butyl-Rubber-Based, Solvent-Release Sealant: ASTM�C�1311. FABRICATION General: Fabricate and finish metal panels and accessories at the factory, by manufacturer's standard procedures and processes, as necessary to fulfill indicated performance requirements demonstrated by laboratory testing. Comply with indicated profiles and with dimensional and structural requirements. Provide panel profile, including major ribs and intermediate stiffening ribs, if any, for full length of panel. Sheet Metal Flashing and Trim: Fabricate flashing and trim to comply with manufacturer's recommendations and recommendations in SMACNA's "Architectural Sheet Metal Manual" that apply to design, dimensions, metal, and other characteristics of item indicated. Form exposed sheet metal accessories that are without excessive oil canning, buckling, and tool marks and that are true to line and levels indicated, with exposed edges folded back to form hems. Seams for Aluminum: Fabricate nonmoving seams with flat-lock seams. Form seams and seal with epoxy seam sealer. Rivet joints for additional strength. Seams for Other Than Aluminum: Fabricate nonmoving seams in accessories with flat-lock seams. Tin edges to be seamed, form seams, and solder. Sealed Joints: Form nonexpansion, but movable, joints in metal to accommodate sealant and to comply with SMACNA standards. Conceal fasteners and expansion provisions where possible. Exposed fasteners are not allowed on faces of accessories exposed to view. Fabricate cleats and attachment devices from same material as accessory being anchored or from compatible, noncorrosive metal recommended in writing by metal panel manufacturer. Size: As recommended by SMACNA's "Architectural Sheet Metal Manual" or metal wall panel manufacturer for application but not less than thickness of metal being secured. FINISHES Protect mechanical and painted finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. Steel Panels and Accessories: Retain one exposed fluoropolymer finish from subparagraphs below. Verify availability of finishes for products specified. If retaining more than one, indicate location of each on Drawings or by inserts. To obtain a proprietary finish system, insert names of coating manufacturers and products. Two-Coat Fluoropolymer: AAMA�621. Fluoropolymer finish containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil (0.019� 0.0013 mm) over 0.2� 0.05 mil (0.05� 0.0013 mm) primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024� 0.0025 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Mica Fluoropolymer: AAMA�621. Two-coat fluoropolymer finish with suspended mica flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil (0.019� 0.0013 mm) over 0.2� 0.05 mil (0.05� 0.0013 mm) primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024� 0.0025 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Metallic Fluoropolymer: AAMA�621. Two-coat fluoropolymer finish with suspended metallic flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil (0.019� 0.0013 mm) over 0.2� 0.05 mil (0.05� 0.0013 mm) primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024� 0.0025 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Finish in "Concealed Finish" Subparagraph below is frequently used as a factory finish for interior surfaces. Concealed Finish: Apply pretreatment and manufacturer's standard white or light-colored acrylic or polyester backer finish consisting of prime coat and wash coat with a minimum total dry film thickness of 0.35 mil (0.009 mm). Aluminum Panels and Accessories: Retain one fluoropolymer finish from subparagraphs below. Verify availability of finishes for products specified. If retaining more than one, indicate location of each on Drawings or by inserts. To obtain a proprietary finish system, insert names of coating manufacturers and products. Revise or insert additional testing requirements in three fluoropolymer subparagraphs below if performance levels indicated in AAMA�2605 are insufficient. Two-Coat Fluoropolymer: AAMA�2605. Fluoropolymer finish containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil (0.019� 0.0013 mm) over 0.2� 0.05 mil (0.05� 0.0013 mm) primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024� 0.0025 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Mica Fluoropolymer: AAMA�2605. Two-coat fluoropolymer finish with suspended mica flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil (0.019� 0.0013 mm) over 0.2� 0.05 mil (0.05� 0.0013 mm) primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024� 0.0025 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. Metallic Fluoropolymer: AAMA�2605. Two-coat fluoropolymer finish with suspended metallic flakes containing not less than 70 percent PVDF resin by weight in color coat applied by panel manufacturer on a continuous coil coating line, with a top side dry film thickness of 0.75� 0.05 mil (0.019� 0.0013 mm) over 0.2� 0.05 mil (0.05� 0.0013 mm) primer coat, to provide a total dry film thickness of 0.95� 0.10 mil (0.024� 0.0025 mm). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. EXECUTION EXAMINATION Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances, metal panel supports, and other conditions affecting performance of the Work. Retain one or both subparagraphs below. Examine wall framing to verify that girts, angles, channels, studs, and other structural panel support members and anchorage have been installed within alignment tolerances required by metal wall panel manufacturer. Examine wall sheathing to verify that sheathing joints are supported by framing or blocking and that installation is within flatness tolerances required by metal wall panel manufacturer. Retain subparagraph below with subparagraph above for systems that depend on air- or water-resistive barriers to prevent air infiltration or water penetration. Verify that air- or water-resistive barriers have been installed over sheathing or backing substrate to prevent air infiltration or water penetration. Examine roughing-in for components and systems penetrating metal panels to verify actual locations of penetrations relative to seam locations of metal panels before installation. Proceed with installation only after unsatisfactory conditions have been corrected. PREPARATION Miscellaneous Supports: Install subframing, furring, and other miscellaneous panel support members and anchorages according to ASTM�C�754 and metal panel manufacturer's written recommendations. METAL PANEL INSTALLATION General: Install metal panels according to manufacturer's written instructions in orientation, sizes, and locations indicated. Install panels perpendicular to supports unless otherwise indicated. Anchor metal panels and other components of the Work securely in place, with provisions for thermal and structural movement. Shim or otherwise plumb substrates receiving metal panels. Flash and seal metal panels at perimeter of all openings. Fasten with self-tapping screws. Do not begin installation until air- or water-resistive barriers and flashings that will be concealed by metal panels are installed. Install screw fasteners in predrilled holes. Locate and space fastenings in uniform vertical and horizontal alignment. Install flashing and trim as metal panel work proceeds. Locate panel splices over, but not attached to, structural supports. Stagger panel splices and end laps to avoid a four-panel lap splice condition. Align bottoms of metal panels and fasten with blind rivets, bolts, or self-tapping screws. Fasten flashings and trim around openings and similar elements with self-tapping screws. Provide weathertight escutcheons for pipe- and conduit-penetrating panels. Fasteners: Steel Panels: Use stainless-steel fasteners for surfaces exposed to the exterior; use galvanized-steel fasteners for surfaces exposed to the interior. Aluminum Panels: Use stainless-steel fasteners for surfaces exposed to the exterior; use stainless-steel fasteners for surfaces exposed to the interior. Metal Protection: Where dissimilar metals contact each other or corrosive substrates, protect against galvanic action as recommended in writing by metal panel manufacturer. Lap-Seam Metal Panels: Fasten metal panels to supports with fasteners at each lapped joint at location and spacing recommended by manufacturer. Lap ribbed or fluted sheets one full rib. Apply panels and associated items true to line for neat and weathertight enclosure. Provide metal-backed washers under heads of exposed fasteners bearing on weather side of metal panels. Locate and space exposed fasteners in uniform vertical and horizontal alignment. Use proper tools to obtain controlled uniform compression for positive seal without rupture of washer. Install screw fasteners with power tools having controlled torque adjusted to compress washer tightly without damage to washer, screw threads, or panels. Install screws in predrilled holes. Flash and seal panels with weather closures at perimeter of all openings. Retain "Watertight Installation" Paragraph below for hydrostatic (watertight) panel installation; delete for water-shedding panel installations. Watertight Installation: Apply a continuous ribbon of sealant or tape to seal lapped joints of metal panels, using sealant or tape as recommend by manufacturer on side laps of nesting-type panels; and elsewhere as needed to make panels watertight. Provide sealant or tape between panels and protruding equipment, vents, and accessories. At panel splices, nest panels with minimum 6-inch (152-mm) end lap, sealed with sealant and fastened together by interlocking clamping plates. Metal Liner Panels: Install panels on [exterior side of girts, with girts exposed to the interior] [interior side of girts with flush appearance on the inside]. Accessory Installation: Install accessories with positive anchorage to building and weathertight mounting, and provide for thermal expansion. Coordinate installation with flashings and other components. Install components required for a complete metal panel system including trim, copings, corners, seam covers, flashings, sealants, gaskets, fillers, closure strips, and similar items. Provide types indicated by metal wall panel manufacturer; or, if not indicated, provide types recommended by metal panel manufacturer. Flashing and Trim: Comply with performance requirements, manufacturer's written installation instructions, and SMACNA's "Architectural Sheet Metal Manual." Provide concealed fasteners where possible, and set units true to line and level as indicated. Install work with laps, joints, and seams that are permanently watertight. Install exposed flashing and trim that is without buckling and tool marks, and that is true to line and levels indicated, with exposed edges folded back to form hems. Install sheet metal flashing and trim to fit substrates and achieve waterproof performance. Expansion Provisions: Provide for thermal expansion of exposed flashing and trim. Space movement joints at a maximum of 10 feet (3�m) with no joints allowed within 24 inches (610 mm) of corner or intersection. Where lapped expansion provisions cannot be used or would not be sufficiently waterproof, form expansion joints of intermeshing hooked flanges, not less than 1 inch (25 mm) deep, filled with mastic sealant (concealed within joints). FIELD QUALITY CONTROL Retain "Testing Agency" Paragraph below to identify who shall perform tests and inspections. If retaining second option below, retain "Field quality-control reports" Paragraph in "Informational Submittals" Article. Testing Agency: [Owner will engage] [Engage] a qualified testing agency to perform tests and inspections. Retain "Water-Spray Test" Paragraph below to check system's resistance to water penetration. Revise indicated test-area requirements to suit Project. Water-Spray Test: After installation, test area of assembly [shown on Drawings] [as directed by Architect] 根据Aamaï501.2的水渗透。保留以下“制造商的现场服务”段落,以便需要工厂授权的服务代表进行测试和检查。制造商的野外服务:聘请工厂授权的服务代表进行测试和检查完成的金属墙板安装,包括配件。拆下并更换金属墙板,测试和检查表明它们不符合指定的要求。在承包商的费用中进行额外的测试和检查,以确定遵守所指定要求的替换或额外工作。准备测试和检查报告。除非在制造商的书面安装说明中另有说明,否则清洁和保护可拆卸临时保护覆盖物和可剥离的薄膜,如果安装了金属面板。完成金属面板安装时,按金属面板制造商推荐的清洁成品表面。在施工期间保持清洁状态。金属面板安装后,清晰的脉冲孔和排水通道的障碍物,污垢和密封剂。 Replace metal panels that have been damaged or have deteriorated beyond successful repair by finish touchup or similar minor repair procedures. END OF SECTION 074213.13     Copyright 2015 AIA MasterSpec Premium 03/15 PRODUCT MASTERSPEC LICENSED BY ARCOM TO BERRIDGE MANUFACTURING COMPANY. FORMED METAL WALL PANELS074213.13 -  PAGE 12 ,-2HV��� �89�������������T���=Na���������4$�$-'7'��������������������������������������������������hg�h�C�h�< h�90J/ h�90J0h�h�heO h�6�0J/h7hh�6�0J/hIu9h�6�0J0 h�6�0J0 h�H�h�9 h�H�h�H� h�95� hxhxhxhx5�hxhxhx5�>* h�90J. h�90J-h�92-3� � � �  � � �   � � l � $ = � �#�@������������������������������)6gdx�D�e����9H#��T�'j�OhP�1P��������������������������)��gdQ=Ggd/SJ��gd�H���P{���a�dS�o� ,!�!�!�"�"4$�$�$�%�%p&y&-'(>(�����������������������������)7'A'B'i(t(�(�(�(�(b+j+�+�+ ,[-k-�-�-�-�-...J.L.M.�.�.�.�.�.�/�/�/�/�/�/�/)0o0p0q0�0�0�0�0������������������»����������������������}t}hn^h�G�0J0hn^h�90J0h[jShn^mH sH hn^mH sH  h�95�h�6�mH sH h)Mh�6�0J:h�6�jh�6�U h�6�h�6� h�H�h�Hh�U� hPV�h�H� h�H�h�H� h/SJh�9 h�u�hg� h�u�h Sh�u�h�9hg�h0l�->(v(�()�)m*�* +X+�+�+�+ ,[-�-�.d/�/�/q01I1�1 282=3�������������������������)gdn^)gd/SJgd�6�)gd�H�)�����0�0�0�0�0/1?1H1�12 2 2�3454@4T4�4�4�4�4�4�4�4�4�4�45552535{5�5�566 6%6)6+6/62646������������������������ǣ����摋�}�vov� h�_�0J/5� h�90J/5� h�_�0J05� h�90J05� h�90J/ h�90J0h�TLhBI>h�H�5�h�H�hn^ hn^h�TL h/SJh�F� h/SJh�H� hPV�h�H� h�H�h�H�h�H�h�95� hn^h�9hn^h�90J0h�9h�u�hn^h�Y0J/hn^h�90J/+=3�3T4�456I6�67�7}8�8�8-9�9F:q:�:�:�:<m=�>�?�����������������������gd�g>)gd�g>gd�g>��)gd/SJ����gd�H�gd�H�����gd�H�)4686<6@6C6F6[6q6t6�6�6�6�6�6�6�6�677777'7R7U7n7q7�7�7�7�7�7�7�7�7&8*8�8�8�8�8�8�8�8�8�8�8999+9-9N9O9|9}9�9�9�9�9�9�9�9���������������˾����������߶߰�ߦߦ������ߟ����������˾������ h/SJh�9huo h�90J/ h�90J0h�H�h�95�h)Mh�|s0J:h�|sjh�|sU h�|sh�|s h�95�h�9 huo0J/5� h�90J/5� h�90J05� huo0J05�>�9�9�9�94:6:D:Y:\:c:e:h:k:l:�:�:�:�:�:�:�:�:; ;n;{;�;�;�;< <�<�<2=k=m=�=�=�=8>:>;>�>�>�>�����������������������������������������z��h�F=h�g>0J:mH sH h�S1h�g>mH sH jh�g>UmH sH hY�mH sH h�g>mH sH h�g>h/SJh�90J/h/SJh�90J0 hn^h�9hn^h�_�0J/hn^h�90J/hn^h�90J0hn^h�_�0J0h�H�h�95� h�95�h�9,�>�> ?????�?�?0@1@2@@@A@P@�@�@0A1A2ALANAOAzA�A�A�A�A�A�AzB|B}B�B�BlCmC�C�C�C�C�CDD*D��������Ϳ���͸�����͠�ߠ�ߠ���}wqw��� h� |0J/ h�90J/ h�90J0h� | h� |h� |h�9h�g>mH sH  hD0J0hDhBI>h�g>5�h�g>0J;>*B*ph� h� h�g>�jhawGh�g>U hawGh�g>jhawGh�g>U hD0J/ h�g>0J/ h�g>0J0h�g>h��h�g>mH sH ,�?�@�@�@�@�@1AOA�A�A}B�B�BmC�D~E�FG�G�HSJ@K�����������������������)gd� |)gd/SJgd�g>)gd�g>gdD��gdD@& gd�g>gd�g>��gd�g>��@& gd/SJ*D4DCDHHH@K|K}K�K�K�K�K8L9L:L;L 0 j₀ 0J/ h�90J/ h�g>0J0 h�90J0h&$h/SJh�rl0J/h�rlh�rl0J/ h�rl0J/h�rlh7hh�rl0J/h/SJh�g>0J0h�9h�g>=�`a4b�b�dg9iCiOijFjk�kylm�mn#n�n�n?pzpZq�q�q r�r��������������������������������gd��)�c�c�c�c�c�c�c�c�c�c�c�c2d@dAdSdVdye�e�e�effffffff#f'f(f^flfmfsf{ff�f)g,g�gh"h#h5h6h;hHhIhMhNhOhVhZh[h�h�h�h�h�h�h�h�t�t�z�z�zQ{�{����������������������������������������������������������������ĺ�į h�95� h�90J/ h�90J0hGXh�9h/SJhL= 0J/ hL= 0J0h�rlhL= 0J/ hL= 0J/h/SJh�g>0J0h�g>hL= h7hhL= 0J/E�rQs�s�s>t�t�uv�v�v�wox�xJycyBz�z*{�{�|�}�؁�ł/�Ńm�����������������������������)���{�{�{��������ʀӀ������ւ�������.�0�=�c�d�f�g�i�j�l�m�o������������������� � ������������������������������������������ž��������������haOmHnHujh�9U h�90J- h�90J.hw]�h�6�>*B*ph� h+,th�6� h�90J, hzL10J+ h�90J*h��jh��Uh�H�h�95� h�90J/ h�90J0 h�95�h�92m����� ������O���J�c�e�f�h�i�k�l�n�o���������������������������������1$If$If$a$gd�6�')���������'Ekd�$$If�A�0����$�P�������������4� Aa�/<0BP��/ ��=!��"��#��$��%����� ���D���y������K� ���y������K� lhttp://www.specagent.com/Lookup?ulid=6911yX��;H�,�]ą'c��V$$If�!vh#v�#vP:V �A��5��5�P4�4� A"B|���������666666666vvvvvvvvv666666>666666666666666666666666666�6666666666�666666666666hH66666666666666666666666666666666666666666666666666666666666666666�62���� 0@P`p������2(�� 0@P`p������ 0@P`p������ 0@P`p������ 0@P`p������ 0@P`p������ 0@P`p��8X�V~��8X�V~�������� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@_HmH nH sH tH <`��< NormalCJ_HmH sH tH DA`���D Default Paragraph FontVi@���V 0 Table Normal :V �4�4� la� (k ���( 0No List 6�O�6 HDR$ ��$*$a$4�O4 FTR$ ��$*$a$0�O"0 SCT$��*$a$<�OR< PRT$$ & F��*$@&a$:�b: SUT$ & F��*$@&a$:�b: DST$ & F��*$@&a$<�Ob< ART$$ & F��*$@&a$F�ObF @PR1$ & F��*$@&a$ mHsHtH6�Or6 PR2$ & F*$@&a$6�O�6 PR3$ & F*$@&a$6��6 PR4$ & F*$@&a$6��6 PR5$ & F*$@&a$8�b8 TB1$� ��*$^� a$8�r8 TB2$�`��*$^�`a$8��8 TB3$����*$^��a$8��8 TB4$����*$^��a$8��8 TB5$� ��*$^� a$8��8 TF1 $� ��*$^� a$8��8 TF2!$�`��*$^�`a$8��8 TF3"$����*$^��a$8��8 TF4#$����*$^��a$8��8 TF5$$� ��*$^� a$&�R& TCH%*$6�b6 TCE&���p�*$^��`�p�0�Or0 EOS'$��*$a$@��@ ANT($��*$a$<�>*B* ph��H�O�H 7PV�CMT)$��*$a$<�B*mHph�sHtH�O�� CPR�O�� SPN�O�� SPD�O�� NUM�O�� NAM �o��� SIB* �o�� IPB*,�O, RJUST1$a$4"4 3zL10Header 2 �H�$.��1. 2zL10 Header Char4 B4 5zL10Footer 4 �H�$.��Q. 4zL10 Footer Char��Ob� 8xTIPJ6��$d%d&d'dN��O��P��Q��B* CJmHph�8sHtHD�/��qD )PV�CMT Char<�B*CJmHph�sHtH4�/���4 6xTIP Char <�B* ph�8>�/���> Or� SustHyperlink >*B* ph�6U`���6 Or�0 Hyperlink >*B*ph�:�o���: �@� SAhyperlink >*B*ph�l ���� w]�PM_CMTd<$��$d!%d$&d!'d$*$-D�M� ����N��!O��$P��!Q��$a$ B*aJph�P��P >�h�0 Balloon Text=CJOJQJaJmHsHtHN�/���N =�h�0Balloon Text CharCJOJQJ^JaJ���� A�F�PRN^? & F$d!%d$&d!'d$-DM� �����N��!O��$P��!Q��$ mHsHtH,�/��, �F�PR1 CharCJ>�/��> ?�F�PRN CharCJfHq� �����PK!��pO�[Content_Types].xml���j�0E����ж�r�(��΢�]��yl��#!MB��;.��n�̽�̨\�A�1&�ҫ�� ���QW���Kv�Ub�OX�#&������1`R��T�9<�l�#��$��>��r�� `�С�-�;c=1g ����?}������~�O���:~���k�ҏM�݄�����������׷�� ���)I0w�K�)K`q���f�ݢ�F�H�b�?����G+D�7�H��Ȍ x�|i���R�LJqbO��Y��PΥ�y�L#���R�=E��6w�R#ϣ����\16h>�((�)����1���!F\OI�1���yA�"֐LəQM�c�@^V6��o#6�ϝ��U�Q �)�F��R���r�����Fr��B7�2aʜ� sn�y��z��?������� rn�y�ӑCv�(Yذ��:� ~%��'L��̼C�9��c_��l��j5x�S�����,�<�̨�Ɋ�VR�ohzB�+~K��O�OI�̲��u�k##7��~F������mKw�����{��� 7�n��_��n�?/���绗�B�x˭k�YW[�d��}N(���'\m�9�����zj���"�Cy'�.ʐ�q2&�""��h;��+�D�pqg�8l�հշ��er�f�k�.Ns��Hl�k~9"G�ڛ��ҽb���5i{�d&���D{=(���!hjew¢kaё�ש�a�ʬ��Ɂ�V��=0#x�B�d��T����y���L�`���M���������v�L$�r3I�Ȩ�c4�Eu���иi�����d(�|PZ���X�6�`�� 4Օ���e�m5}(�-z���0Y@�p��E4��g����6ʲȸ"�W���AB�J��+�_���JC�z�%�Y���A��$���BO�6"#�����Za���o��l �ijK�.��J�o�eg����z�����m�o�1���QT5��#��Q�Qt1��J�K:ꬌ�vV����h�g�l�zP�nZv���ޮ{����&���i���v3fX���Xޮ�k��!M�;|.�ے�]k��>���2~��{���Q�LfP��weXjv1j�����v�&��~k�v+ne��N����`�]�04_�+U�՗��;{ �1���K*�J%|z�l�&jO���"�Dqk����H�}]��^���J��*^ӫU:~�Y��~�>���������uË(�*�����/��]۽�%U���Tq��������! :�[�q���*�f\�N���a+h����t�o\�B��~3�Z�N�U��תI��n��5}����b+�壈�W�:���PK! ѐ��'theme/theme/_rels/themeManager.xml.rels��M �0���wooӺ�&݈Э���5 6?$Q�� �,.�a��i����c2�1h�:�q��m��@RN��;d�`��o7�g�K(M&$R(.1�r'J��ЊT���8��V�"��AȻ�H�u}��|�$�b{��P����8�g/]�QAsم(����#��L�[������PK-!��pO�[Content_Types].xmlPK-!�֧��6 -_rels/.relsPK-!ky���theme/theme/themeManager.xmlPK-!o(ʾ���theme/theme/theme1.xmlPK-! ѐ��'� theme/theme/_rels/themeManager.xml.relsPK]� ������ ������7'�046�9�>*D�Z�c�{�FJLNOPRTVX�P>(=3�?@K�`�rm���GHIKMQSUWYZ&L&�&�.�./N1|1�1�5:6�6�718@8|C�C8D�X��X��X��X��X��X������!���8�@�����������0�( ��A��+� ��B �S ���� ?���userSustainabilityTopic_7_1userSustainabilityTopic_30_1ptBookmark6933ptBookmark6911� $T,�7�7 �%�,19��(�(�(�(�(�(�()4)7)�)�)�,�,�-�-l2o2�8�8�8�8�8�8�8�8�89@@I@�A@C �@C h�k�k�l�m�mnJqbq*s�s�s�t�uw�z.{�{l|�|�}�}~ ~�~�~�~�~N�O�����I�c�e�f�h�i�k�l�n�o������B�������������x ���^�`�OJQJo( �8�����^�8`���OJQJo(��������^�`���OJQJ^Jo(o �� ����p^�� `���OJQJo(�� �� ����@ ^�� `���OJQJo(�� �x����^�x`���OJQJo(���H�����^�H`���OJQJ^Jo(o ������^�`���OJQJo(�� �������^��`���OJQJo(�� PART -  SCHEDULE  - PRODUCT DATA SHEET  - �`����`^�``���.�`����`^�``���.�������^��`���.�������^��`���.� ���� ^� `���)�` ����` ^�` `���)���������������}�|�:l�[�2RPn^� aOiD�`x��!L= _ &$xM)�,�Y-~|/�1zL1. 2S 3`C4mJ5�9|^9�K;�<�g>Q=G�H/SJJ�TLeOrQ�VR S T�HT&9U]VGXa&b�Zc�HfOLiWl�rl�,nuo�Hp;Vr�ms�|s+,t�,tstt0/u�Ovxv� |�Y�_���&%�lV�n-��Q��O��u��@��w�g��U�� �[$�Or�?>��h�s�0l��� V�w)�oa�v2��3�wS��>��A���o���h?�K��H�J�Fr��1�0 ��_��F�� �w]��R��C�UY��6��G��T��Z�n��Y�;J���PV�je�&�<�zD�Y�c�e��� DOIFormatMF04MF95MFOrigin SectionIDSpecTypeuserSustainabilityVar_30_1userSustainabilityVar_7_1Version03/01/1510742131307415MF04175 MasterSpec�30^userSustainabilityTopic_30_1^1,^<SustainabilityTopic id="30"><TopicText id="239"><RatingSystems><System id="1"/></RatingSystems> <Content><CMT>Retain "Recycled Content" Paragraph below to specify recycled content if required. An alternative method of requiring recycled content is to retain requirement in Project's Division�01 sustainable design requirements Section that gives Contractor the option and responsibility to determine how recycled content requirements will be met.</CMT><PR1>Recycled Content: Postconsumer recycled content plus one-half of preconsumer recycled content not less than &lt;Insert value&gt; percent.</PR1></Content> </TopicText></SustainabilityTopic>-7^userSustainabilityTopic_7_1^1,^<SustainabilityTopic id="7"><TopicText id="168"><RatingSystems><System id="1"/></RatingSystems> <Content><PR2>Product Data: For recycled content, indicating postconsumer and preconsumer recycled content and cost.</PR2></Content> </TopicText></SustainabilityTopic>11743�@��,�,�~�,�,��@��Unknown������������G��*�Ax� �Times New Roman5��Symbol3� �*�Cx� �Arial5� �.�[`�)�Tahoma?� �*�Cx� �Courier New;��WingdingsA����$B�Cambria Math"���hhقF�قF�On B�On B����r!�!�K�Q������HP �� $P����������������������zL1 !xx�^ ���,SECTION 074213.13 - FORMED METAL WALL PANELSFORMED METAL WALL PANELSBAS-12345-MS80 ARCOM, Inc.Microsoft Office User  �� �����Oh��+'��0�����, LX | � �����'0SECTION 074213.13 - FORMED METAL WALL PANELSFORMED METAL WALL PANELS ARCOM, Inc.BAS-12345-MS80 Normal.dotmMicrosoft Office User2Microsoft Macintosh Word@F�#@�Ԡ���@�Ԡ��� On�� ��՜.��+,��D��՜.��+,��p, px����� ���� � ' Microsoft0�B!� -SECTION 074213.13 - FORMED METAL WALL PANELS Title, 8@ _PID_HLINKS'A�$)*Whttp://www.berridge.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdfy *http://www.specagent.com/Lookup?ulid=6911)* Whttp://www.berridge.com/wp-content/uploads/2014/06/Approved-Materials-Form-11-4-13.pdf( http://www.berridge.com/colors/( http://www.berridge.com/colors/GQ9http://www.berridge.com/technical/testing-summary-chart/  !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[����]^_`abc����efghijklmnopqrstuvwxyz{|}~���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������Root Entry�������� �F�r+������Data ������������\1Table����d?WordDocument����1�SummaryInformation(�������������DocumentSummaryInformation8���������CompObj������������r������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ ���� �F Microsoft Word 97-2004 Document MSWordDocWord.Document.8�9�q